曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-23-15-010-052
 C. Get Access
 (1) Make sure that the access platform is in position below the APU compartment.
 (2) Make sure that the APU access doors 315AL and 316AR are open (Ref. TASK 52-41-00-010-001).
 (3) Make sure that the light SW 11LJ is set to the ON position.
 4. Procedure_________ 
R  (Ref. Fig. 401/TASK 49-23-15-991-001) 
R  **ON A/C 001-003, 051-099, 
R  (Ref. Fig. 402/TASK 49-23-15-991-002) 
R  **ON A/C 001-003, 051-099, 401-499,
 Subtask 49-23-15-420-050
 A. Installation of the Load-Compressor Inlet Temperature-Sensor (8011KM)
 (1) Clean the component interface and/or the adjacent area.
 (2) Do an inspection of the component interface and/or the adjacent area.
 (3) Install the new packing (9) and packing (8) to the load-compressor inlet temperature-sensor (8011KM) (1).
 (4) Install the load-compressor inlet temperature-sensor (8011KM) (1). 

 

____ containment shield was removed previously. Otherwise continue with step B.
 (a)
 Remove the blanking caps and connect the electrical connectors (7).

 (b)
 Make sure that the electrical connectors are clean and in the correct condition.

 (c)
 Install the washers (3) and (6), the nuts (4) and (5).

 (d) Tighten the nuts (4) and (5). R **ON A/C 001-003, 051-099,
 Subtask 49-23-15-410-051
 B. Installation of the bottom Load-Compressor Containment-Shield (if previously removed)
 (1)
 Move the notched end of bottom load-compressor containment-shield

 (14) carefully past the witness drain tube and under the LCIT wiring.

 (2)
 Adjust the load-compressor containment shield to align the shield spacer with the bleed-duct assy bolt (10) hole.

 (3)
 Loosely attach the load-compressor containment shield (14) with the bolts (10) and (15).

 (4)
 Make sure that the L-bracket (16) overlaps the outer diameter of the load-compressor containment-shield (14). Tighten the bolt (17).

 (5)
 Attach the bolts (11) and (18).

 (6)
 Install the clamp (12) of the LCIT wiring with bolt (13).

 (7)
 Torque all bolts to 80 lbf.in (0.90 m.daN).

 (8)
 Remove the blanking caps and connect the electrical connectors (7).

 (9)
 Make sure that the electrical connectors are clean and in the correct

 

 

 condition.
 (10) Install the washers (3) and (6), the nuts (4) and (5).
 (11) Tighten the nuts (4) and (5). R **ON A/C 001-003, 051-099, 401-499,
 Subtask 49-23-15-865-052
 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.
 Subtask 49-23-15-710-050
 D. Do the Self Test of the ECB (Ref. TASK 49-00-00-710-001).
 5. Close-up
________
 Subtask 49-23-15-410-050

 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Set the LIGHT control switch 11LJ to the OFF position.

 (3)
 Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).

 (4)
 Remove the access platform(s).
 Subtask 49-23-15-865-056

 B.
 Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41

 Subtask 49-23-15-860-052
 C. Aircraft Maintenance Configuration
 (1)
 De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).

 (2)
 Pressurize the reservoirs of the hydraulic systems. (Ref. TASK 29-14-00-614-002).

 (3)
 Remove the warning notice(s).

 

 SENSOR - LOAD COMPRESSOR DISCHARGE TEMPERATURE - REMOVAL/INSTALLATION
_____________________________________________________________________

R **ON A/C 001-003, 051-099, 401-499,
 TASK 49-23-16-000-001
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(114)