(2)
 Close the access door 314AR.

 (3)
 Close the APU access doors 316AR, 315AL (Ref. TASK 52-41-00-410-001).

 (4)
 Remove the access platform(s).

 (5)
 Remove the warning notice(s).

 Subtask 49-16-42-860-053
 B. Aircraft Maintenance Configuration
 (1) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).

 FLAP - AIR INTAKE - REMOVAL/INSTALLATION
________________________________________
R **ON A/C 001-003, 051-099, 401-499,
 TASK 49-16-43-000-001
 Removal of the Air Intake Flap (GTCP 36-300)

 1.
 Reason for the Job

__________________
 Self explanatory.

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific access platform 3.5 m (11 ft. 6 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
 Configuration before Maintenance Action
 52-41-00-010-001 Open the APU Doors for Access
 49-16-43-991-001 Fig. 401

 3. Job Set-up
__________ Subtask 49-16-43-860-055
 A. Aircraft Maintenance Configuration
 (1)
 Put a warning notice on the panel 25VU to tell persons not to start the APU.

 (2)
 Energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-861-002).

 (3)
 De-pressurize the hydraulic systems (Ref. TASK 29-00-00-864-001). Subtask 49-16-43-865-050

 B.
 Open, safety and tag this(these) circuit breaker(s):

 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-16-43-010-050-A
 C. Get Access
 (1)
 Put the access platform in position below the APU compartment.

 (2)
 Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).

 (3)
 Set the LIGHT control switch 11LJ to the ON position.

 4. Procedure
_________ (Ref. Fig. 401/TASK 49-16-43-991-001) Subtask 49-16-43-020-053
 A. Removal of the Air Intake Flap
 (1) Remove the actuator spindle (1) from the air intake flap (8). NOTE : Get access through the APU air intake in the fire wall at
____
 FR80.

 Air Intake Flap
 Figure 401/TASK 49-16-43-991-001

 CES

 (a)
 Remove and discard the cotter pin (3).

 (b)
 Remove the castle nut (4), the washer (5) the bolt (6) and disconnect the actuator spindle (1) from the air intake flap (8).

 (2) Hold the air intake flap (8), remove the screws (7) and then the air intake flap (8) from the air inlet duct (2).

 TASK 49-16-43-400-001
 Installation of the Air Intake Flap (GTCP 36-300)
 1. Reason for the Job
__________________
 Self explanatory.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific access platform 3.5 m (11 ft. 6 in.)
 No specific Torque Wrench : range 0.00 to 1.20 m.daN

 (0.00 to 9.00 lbf.ft)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004  USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(12)