(2)
 Install the bolt (6) and the bolts (5) and (3) and the washers (4) and (2).

 (3)
 Install the top flange (20) and the bottom flange (29) around the air intake duct (1).

 (4)
 Install the bolts (26) and the washers (27). Do not fully tighten the bolts at this time.

 (5)
 Install the bolts (24) and the washers (23). Do not fully tighten the bolts at this time.

 (6)
 Install the bolts (18) and the washers (19) to the anchor nuts. Tighten all screws and bolts.

 (7)
 Install the seal (13) on the flange (14) and install the distance washers (32) at the lower holes of the seal.

 (8)
 Install the frame (12) on the flange (14).

 (9)
 Apply SEALANTS (Material No. 09-016):

 -to fill gaps which remain in the area of the flange (14) and the frame of the air intake duct (1).
 (10)
 Install the bolts (10), the washers (11) (15) and the nuts (16). Tighten the bolts equally.

 (11)
 Install the flange (14) with the screws (28), the washer (30) and the nuts (31) on the air intake duct (1).

 (12)
 Apply SEALANTS (Material No. 09-016) to all locations from which the sealant was removed.

 (13)
 Seal the bonding connections with SEALANTS (Material No. 09-016) and then apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001).

 (14)
 Install the air intake nose (Ref. TASK 49-16-44-400-001).

 (15)
 Install the air intake flap (Ref. TASK 49-16-43-400-001).

 (16)
 Apply SPECIAL MATERIALS (Material No. 05-005) around the screw heads at the inner side of the air intake duct.

 **ON A/C 051-051,
 Subtask 49-16-42-420-050-A
 B. Installation of the Air Intake Duct
 (1)
 Put the air intake duct (1) into position and hold it.

 (2)
 Install the bolts (21) and (22) and the washers (20) and (23).

 (3)
 Install the top flange (17) and the bottom flange (18) around the air intake duct (1).

 (4)
 Install the bolts (4) and the washers (3). Do not fully tighten the bolts at this time.

 (5)
 Install the bolts (9), the washers (8) and the screws (19). Do not fully tighten the bolts at this time.

 (6)
 Install the bolts (7), the washers (6) to the anchor nuts (5). Tighten all screws and bolts.

 (7)
 Install the flexible seal (14) on the flange (15) and install the distance washers (16) at the lower holes of the seal.

 (8)
 Install the brackets (12) with the flanged edge to the outer side.

 (9)
 Install the bolts (13), the washers (11) and the nuts (10). Tighten the bolts equally.

 (10)
 Install the flange (15) with the screws (2) on the air intake duct (1).

 (11)
 Apply SEALANTS (Material No. 09-016) to all locations from which the sealant was removed.

 (12)
 Seal the bonding connections with SEALANTS (Material No. 09-016) and then apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001).

 (13)
 Install the air intake nose (Ref. TASK 49-16-44-400-001).

 (14)
 Install the air intake flap (Ref. TASK 49-16-43-400-001).

 (15)
 Apply SPECIAL MATERIALS (Material No. 05-005) around the screw heads at the inner side of the air intake duct. **ON A/C 051-051,

 Post SB 49-1050 For A/C 051-051, Subtask 49-16-42-420-050-B
 B. Installation of the Air Intake Duct
 (1)
 Put the air intake duct (1) into position and hold it.

 (2)
 Install the bolt (6) and the bolts (5) and (3) and the washers (4) and (2).

 (3)
 Install the top flange (20) and the bottom flange (29) around the air intake duct (1).

 (4)
 Install the bolts (26) and the washers (27). Do not fully tighten the

 bolts at this time.

 (5)
 Install the bolts (24) and the washers (23). Do not fully tighten the bolts at this time.

 (6)
 Install the bolts (18) and the washers (19) to the anchor nuts.
 Tighten all screws and bolts.

 (7)
 Install the seal (13) on the flange (14) and install the distance
 washers (32) at the lower holes of the seal.

 (8)
 Install the shims (17) and the frame (12) on the flange (14).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(6)