______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.5 m (11 ft. 6 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
 Configuration before Maintenance Action 52-41-00-010-001 Open the APU Doors for Access 49-16-44-991-003 Fig. 401
 3. Job Set-up
__________ Subtask 49-16-44-860-055
 A. Aircraft Maintenance Configuration
 (1)
 Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

 (2)
 On the panel 25VU, put the APU Master SW p/bsw to the ON position.

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-16-44Page 401 201-210, Config-2 Aug 01/05
 CES

 (3)
 Put a warning notice in the cockpit to tell persons not to start the APU.

 (4)
 Make sure that hydraulic systems are depressurized
 (Ref. TASK 29-00-00-864-001).

 Subtask 49-16-44-865-056
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-16-44-010-052
 C. Get Access
 (1)
 Put the access platform in position below the APU compartment.

 (2)
 Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).

 4. Procedure
_________ Subtask 49-16-44-020-052
 A. Removal of the Air Intake Nose
 (Ref. Fig. 401/TASK 49-16-44-991-003)

 (1)
 Remove the screws (7 and 8), the washers (6 and 9), the end-profile

 (5) and the bracket (4).

 (2)
 Remove the screws (1).

 (3)
 Remove the bolts (10), the washers (11) and the nuts (12).

 (4)
 Remove the screws (3) and the washers (2).

 (5)
 Remove the air intake nose (13) from the air inlet duct (14).

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-16-44Page 402 201-210, Config-2 Aug 01/05
 CES

 Air Intake Nose
 Figure 401/TASK 49-16-44-991-003

 CES  TASK 49-16-44-400-003

 Installation of the Air Intake Nose (131-9(A))
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific wooden or plastic scraper
 No specific access platform 3.5 m (11 ft. 6 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-002 USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00) Material No. 05-005 USA MIL-C-16173 GRADE II CORROSION PREVENTIVE (Ref. 20-31-00)
 Material No. 07-001 ELECTRICAL BONDING COATING (BLUE COLOR) (Ref. 20-31-00)
 Material No. 09-016  USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
 Material No. 09-018  USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT (Ref. 20-31-00)
 Material No. 11-001  USA MIL-D-16791 TYPE I DETERGENT (Ref. 20-31-00)

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-16-44Page 404 201-210, Config-2 Aug 01/05
 CES

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(23)