(a)
 Remove the screws which attach the cover plate to the forward face of the starter motor (8KA).

 (b)
 Remove the cover plate from the forward face of the starter motor (8KA).

 (4)
 Attach the socket spanner on the extension of the starter motor shaft. Turn the socket spanner counterclockwise to turn the engine.

 (5)
 Put the borescope through the air intake access hole to examine the power compressor for this damage:

 (a)
 Compressor blades with leading-edge erosion more than 0.125 in. (3.1749 mm) or trailing-edge erosion more than 0.5 in. (12.6999 mm), are not permitted.

 (b)
 Leading-edge cracks are permitted if they are in the outer 50% of the blade.

 (c)
 Trailing-edge cracks less than three-eighths of the blade are permitted if they are in the area between the shroud and three-quarters of the exit blade width.

 (d)
 Compressor blade/splitters that have more than one crack which would permit a piece of the blade to break off, are not permitted.

 (6)
 Remove the borescope from the power section compressor. Subtask 49-20-00-290-061

 B.
 Borescope Inspection of the Turbine Nozzle

 (1)
 Remove the igniter plug (8031KM) to get access to the turbine nozzle (Ref. TASK 49-41-41-000-001).

 (2)
 Assemble the GUIDE TOOL - BORESCOPE, APU and install it in position at the igniter plug hole.

 (3)
 Put the borescope in position at the nozzle guide vanes and make an inspection for this damage:

 (a)
 Cracks on vane leading-edges fillets are not permitted.

 (b)
 Cracks and/or erosion on vane leading-edges are permitted if they do not go into the vane air-cooling passages.

 (c)
 Pits and erosion along the blade length and trailing edges are permitted.

 (d)
 Broken vanes or missing pieces of the vane leading-edges are not permitted.

 (4)
 Remove the borescope from the Auxiliary Power Unit (APU) - (4005KM).

 (5)
 Install the igniter plug (8031KM) (Ref. TASK 49-41-41-400-001).

 (6)
 Remove the socket spanner from the extension on the starter motor (8KA).

 (7)
 Install the cover plate to the front face of the starter motor (8KA) with the screws.

 (8)
 Tighten the screws.

 (9)
 Install the air-intake screen (3) to the air-intake with the washers

 (2) and the screws (1).

 5. Close-up
________ Subtask 49-20-00-410-057
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2)
 Close the APU access door 316AR (Ref. TASK 52-41-00-410-001). Subtask 49-20-00-865-063

 B.
 Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.

 Subtask 49-20-00-790-051
 C. Test
 (1)
 Start the APU (Ref. TASK 49-00-00-860-003).

 (2)
 Examine the APU pipeline connections for leaks.
 NOTE : No leaks are permitted.

____
 (3)
 Stop the APU (Ref. TASK 49-00-00-860-004). Subtask 49-20-00-865-064

 D.
 Open, safety and tag this(these) circuit breaker(s):

 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-20-00-410-058
 E. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the APU access door 315AL (Ref. TASK 52-41-00-410-001).

 (3)
 Remove the access platform(s). Subtask 49-20-00-865-065

 F.
 Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.

 Subtask 49-20-00-860-076
 G. Aircraft Maintenance Configuration
 (1)
 De-energize the ground service network
 (Ref. TASK 24-42-00-862-001).

 (2)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 (3)
 Remove the warning notice(s).

 ENGINE ((APS 3200)) - INSPECTION/CHECK
______________________________________
 TASK 49-20-00-210-001
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(84)