(f)
Tighten the screws (18).
(g)
Seal the screws (18) with the SEALANTS (Material No. 09-016).
(h)
Apply SPECIAL MATERIALS (Material No. 05-005) around the
screwheads.
Subtask 49-16-43-420-050
C. Installation of the Air Intake Flap
(1) Protective Treatment
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(a) Apply SPECIAL MATERIALS (Material No. 05-002) to all attaching parts.
(2)
Put the air intake flap (8) in position and hold it.
(3)
Install the screws (7). Do not tighten the screws at this time.
(4)
Make sure that the:
-clearance C (between the trailing edge of the air intake flap (8) and the air intake nose) is between 0.5 mm (0.0196 in.) and 1.5 mm (0.0590 in.).
-left and right clearance A (between the air intake flap (8) and the air inlet duct (2)) is between 1.5 mm (0.0590 in.) and 2.5 mm (0.0984 in.).
If necessary, adjust the clearance C and A as follows:
(a) Adjust the clearance C and A.
NOTE : Make sure that the change of profile from the diverter to
____ the air intake flap (in the open position) stays smooth.
(b) Tighten only the outer screws (7).
(5) Attach the actuator spindle (1) to the air intake flap (8).
NOTE : Get access through the APU air intake in the fire wall at
____
FR80.
(a)
Connect the actuator spindle (1) to the air intake flap (8).
(b)
Apply COMMON GREASE (Material No. 04-004) to the bolt (6) and install the bolt (6), the washer (5) and the castle nut (4).
(c)
TORQUE the castle nut (4) to between 0.7 and 0.8 m.daN (61.94 and
70.79 lbf.in) and safety it with a new cotter pin (3).
(6)
Open the air intake flap (8) electrically.
(a)
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 121VU...APU/APU/CTL...(2KD)...L42 121VU...APU/ECB/SPLY..(1KD)...L41
(b)
Push the APU MASTER SW pushbutton switch on the panel 25VU to the ON position.
(c)
Wait until the air intake flap (8) is fully open.
(d)
Open, safety and tag this(these) circuit breaker(s):
121VU...APU/APU/CTL...(2KD)...L42
121VU...APU/ECB/SPLY..(1KD)...L41
(7)
Make sure that the maximum permitted deviation B (between the air inlet flap (8)and the inner top wall of the air inlet duct (2)) is
1.0 mm (0.0393 in.).
NOTE : Adjust the air inlet flap by increasing or decreasing the
____
length of the actuator spindle (1).
(8)
Tighten all screws (7).
(9)
Close the air intake flap (8) electrically.
(a)
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 121VU...APU/APU/CTL...(2KD)...L42 121VU...APU/ECB/SPLY..(1KD)...L41
(b)
Release the APU MASTER SW pushbutton switch on the panel 25VU to the OFF position.
(c)
Wait until the air intake flap (8) is fully closed.
(d)
Open, safety and tag this(these) circuit breaker(s):
121VU...APU/APU/CTL...(2KD)...L42
121VU...APU/ECB/SPLY..(1KD)...L41
(10) Adjust the seal profile (15) to the air intake nose with the flap in the closed position. The seal profile must touch the air intake nose with maximum 0.5 mm (0.0196 in.) compression F .
Subtask 49-16-43-865-052
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 121VU...APU/APU/CTL...(2KD)...L42 121VU...APU/ECB/SYPL..(1KD)...L41
Subtask 49-16-43-710-050
E. Do the operational test (Ref. TASK 49-16-00-710-001).
5. Close-up
________ Subtask 49-16-43-910-051
A. Application of the Surface Protection
(1)
Apply SEALANTS (Material No. 09-016) to all the nuts, washers and screwheads.
(2)
Apply SPECIAL MATERIALS (Material No. 05-005) around all screwheads.
(3)
Seal the bonding connections (Ref. TASK 20-28-00-912-004). Subtask 49-16-43-410-050-A
B.
Close Access
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(14)
