(2)
Make sure that hydraulic systems are depressurized
(Ref. TASK 29-00-00-864-001).
(3)
Make sure that the access platform is in position below the access doors 315AL and 316AR.
(4)
Make sure that the access doors 315AL and 316AR are open (Ref. TASK 52-41-00-010-001).
(5)
Make sure that the APU air intake flap is in open position.
R EFF : 001-049, 101-105, 107-107, 151-199, 49-16-44Page 405 201-210, Config-2 Aug 01/05
CES Subtask 49-16-44-865-057
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
4. Procedure
_________
(Ref. Fig. 401/TASK 49-16-44-991-003) Subtask 49-16-44-910-055
A. Preparation for Installation
(1)
Remove the old sealant. Use the solvent CLEANING AGENTS (Material No. 11-001) and a wooden or plastic scraper.
(2)
Clean the component interface and/or the adjacent area.
(3)
Apply SPECIAL MATERIALS (Material No. 05-002) to all screws and washers.
(4)
Apply the SEALANTS (Material No. 09-018) to the mating surfaces of the air intake nose (13), the bracket (4) and the end profile (5).
Subtask 49-16-44-420-052
B. Installation of the Air Intake Nose
(Ref. Fig. 401/TASK 49-16-44-991-003)
(1)
Put the air intake nose (13) in position and hold it.
(2)
Install the screws (1). Do not fully tighten the screws at this time.
(3)
Install the screws (3) and the washers (2). Do not fully tighten the screws at this time.
(4)
Install the bracket (4) and the end-profile (5) with the screws (7 and 8) and the washers (6 and 9).
(5)
Install the bolts (10), the washers (11) and the nuts (12).
R EFF : 001-049, 101-105, 107-107, 151-199, 49-16-44Page 406 201-210, Config-2 Aug 01/05
CES
(6)
Tighten all screws and bolts. Subtask 49-16-44-910-056
C.
Application of the Surface Treatments
(1)
Apply SEALANTS (Material No. 09-016) to all locations, where removed, when dry apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001).
(2)
Apply the SEALANTS (Material No. 09-016) to all the nuts, washers and screwheads.
(3)
Apply the SPECIAL MATERIALS (Material No. 05-005) to all the screwheads.
5. Close-up
________ Subtask 49-16-44-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Set the LIGHT SW 11LJ to the OFF position.
(3)
Close the APU access doors 316AR, 315AL (Ref. TASK 52-41-00-410-001).
(4)
Remove the access platform(s). Subtask 49-16-44-865-058
B.
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.
Subtask 49-16-44-860-056
C. Aircraft Maintenance Configuration
(1)
Pressurize the reservoirs of the hydraulic systems.
(Ref. TASK 29-14-00-614-002).
(2)
De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
R EFF : 001-049, 101-105, 107-107, 151-199, 49-16-44Page 407 201-210, Config-2 Aug 01/05
CES
(3) Remove the warning notice(s).
R EFF : 001-049, 101-105, 107-107, 151-199, 49-16-44Page 408 201-210, Config-2 Aug 01/05
CES
NOSE - AIR INTAKE - REMOVAL/INSTALLATION
________________________________________ TASK 49-16-44-000-002 Removal of the Air Intake Nose (APS 3200)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(24)
