(3)
 If inspection reveals missing or loose pins and/or loose or distressed splitters for only the lower half plenum, replacement of this part on wing is approved for post service bulletin 4500001-49-58 plenums. These plenums are identified as follows:

 -
Plenum lower half part number 0332227730 with "SB 58" marked beside or near the plenum half part marking or

 -
Plenum lower half part number 0332227960 NOTE : LOWER INLET PLENUM WITH DIFFERENT PART NUMBERS THAN P/N

____ 0332227730 (with SB58) OR P/N 0332227960 CANNOT INTERCHANGE.
 5. Close-up
________ Subtask 49-16-48-410-052
 A. Close Access
 (1)
 If removed, install the lower inlet-plenum (Ref. TASK 49-16-48-400-002).

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Close the access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).

 (4)
 Remove the access platform(s).

 Lower Inlet-Plenum Figure 402/TASK 49-16-48-991-003 
R  EFF :  106-149, 211-299, 301-399, 401-499,  49-16-48 Page 412 Aug 01/05
 CES 

 Subtask 49-16-48-865-057
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD
 Subtask 49-16-48-860-058
 C. Aircraft Maintenance Configuration
 (1)
 Pressurize the reservoirs of the hydraulic systems.
 (Ref. TASK 29-14-00-614-002).

 (2)
 De-energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-862-002).

 (3)
 Remove the warning notice(s).

 ACTUATOR - AIR INTAKE FLAP ((GTCP 36-300)) - MAINTENANCE PRACTICES
__________________________________________________________________
R **ON A/C 001-003, 051-099, 401-499,
 TASK 49-16-51-000-001
 Removal of the Air-Intake Flap Actuator (4015KM) (GTCP 36-300)

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific blanking caps
 No specific circuit breaker(s) safety clip(s)
 No specific access platform 2.5 m (8 ft. 2 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
49-16-51-991-001 Fig. 201
 3. Job Set-up
__________
 Subtask 49-16-51-865-050

 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41

 Subtask 49-16-51-010-050
 B. Get Access
 (1)
 Put the access platform in position below the APU compartment.

 (2)
 Open the maintenance door 314AR.

 (3)
 Release the 22 stud fasteners and remove the catwalk panel from the service panel.

 4. Procedure
_________
 (Ref. Fig. 201/TASK 49-16-51-991-001) Subtask 49-16-51-020-051
 A. Removal of the Air Intake Actuator (4015KM)
 (1)
 Disconnect the electrical connector (18).

 (2)
 Put blanking caps on the disconnected electrical connectors.

 (3)
 Remove the screw (20), the washer (19) and disconnect the bonding jumper (21).

 (4)
 Remove the clamp (11) and push the bellows (12) down.

 (5)
 Remove and discard the cotter pins (1) and (17).

 (6)
 Remove the castle nut (16), the washers (15), (9A) and the bolt (10).

 (7)
 Remove the castle nut (2), the washers (3) and (4) and the bolt (5).

 (8)
 Remove the air-intake flap actuator (4015KM) (6).

 5. Close-up
________

 INTENTIONALLY BLANK

 Air-Intake-Flap Actuator.
 Figure 201/TASK 49-16-51-991-001- 12 (SHEET 1)

 CES

 Air-Intake-Flap Actuator.
 Figure 201/TASK 49-16-51-991-001- 22 (SHEET 2)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(43)