2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 1 l (0.25 USgal) No specific protective covers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-73-49-991-308 Fig. 409
3. Job Set-up
__________ Subtask 71-73-49-941-061
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
F 『 EEFF : ALL E Page 46571-73-49
E E Feb 01/00 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 71-73-49-010-061
B. Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
4. Procedure
_________
(Ref. Fig. 409/TASK 71-73-49-991-308)
Subtask 71-73-49-020-060
A. Removal of the Forward Oil Sump Drain Tube
(1) Put a container 1 l (0.25 USgal) below the drain reservoir module to catch any oil remaining in the tube.
(2) Disconnect the forward oil sump drain tube (20) from the manifold oil drain tube and let the fluid drain into the container.
(3) Remove the bolt (10), the nut (15) and the clamp (5) that attach the drain tube (20) to the bracket on the fan case.
(4) Disconnect the drain tube (20) from the forward sump drain.
(5) Remove the forward oil sump drain tube (20) from the engine.
(6) Put protective covers on the forward sump fitting, and the drain tubes.
(7) Remove the container from below the drain reservoir module.
F 『 EEFF : ALL E Page 46671-73-49
E E Feb 01/00 ERE
ECES E F 『 E C F M E E E E 56-5B E
Forward Oil Sump Drain Tube Figure 409/TASK 71-73-49-991-308
F EEFF : E ER ECES ALL 『E 71-73-49EE E Page 467 Feb 01/00
F 『
E C F M E
E E
E 56-5B E
E E
TASK 71-73-49-400-029
Installation of the Forward Oil Sump Drain Tube
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
R No specific Torque Wrench : range 5.00 to 35.00 lbf.in
R (0.05 to 0.40 m.daN) No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
71-73-49-991-308 Fig. 409
3. Job Set-up
__________
Subtask 71-73-49-860-058
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
F 『 EEFF : ALL E Page 46871-73-49
E E May 01/05 E E ECES E Subtask 71-73-49-010-076
F 『
E C F M E
E E
E 56-5B E
E E
B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(122)
