F 『
E C F M E
E E
E 56-5B E
E E
TASK 71-73-49-400-049 Installation of the Reservoir to Manifold Hydraulic Oil Drain Tube
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 71-73-49-991-309 Fig. 410
3. Job Set-up
__________ Subtask 71-73-49-860-059
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
F 『 EEFF : ALL E Page 47471-73-49
E E Feb 01/00 ERE
ECES E Subtask 71-73-49-010-077
F 『
E C F M E
E E
E 56-5B E
E E
B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
4. Procedure
_________
(Ref. Fig. 410/TASK 71-73-49-991-309) Subtask 71-73-49-420-061
A. Installation of the Reservoir to Manifold Hydraulic Oil Drain Tube
(1) Remove the protective covers from the drain manifold module, the drain reservoir module, and the drain tube (5).
(2) Connect the reservoir to manifold hydraulic oil drain tube (5) to the drain reservoir module. Do not torque the coupling nut at this time.
(3) Connect the drain tube (5) to the drain manifold module. Do not torque the coupling nut at this time.
(4) Make sure that the drain tube (5) is aligned correctly on the engine.
(5) Torque the drain tube coupling nuts CAUTION : USE A SECOND WRENCH TO HOLD THE FITTINGS WHEN YOU
_______ LOOSEN/TIGHTEN THE TUBE COUPLING NUTS. THIS PREVENTS DAMAGE TO THE TUBES.
(a) TORQUE the drain tube (5) coupling nuts to between 200 and 250 lbf.in (2.26 and 2.82 m.daN).
F 『 EEFF : ALL E Page 47571-73-49
E E Feb 01/00 ERE
ECES E 5. Close-up
F 『
E C F M E
E E
E 56-5B E
E E
________ Subtask 71-73-49-410-062
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3) Remove the warning notice(s).
F 『 EEFF : ALL E Page 47671-73-49
E E Feb 01/00 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E E E TASK 71-73-49-000-001
Removal of the Reservoir to Manifold Oil Drain Tube
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 1 l (0.25 USgal) No specific protective covers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-73-49-991-310 Fig. 411
3. Job Set-up
__________ Subtask 71-73-49-941-063
A. Safety Precautions
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(124)
