(2) Disconnect the electrical connector 4004VC-A from the junction box at station 176.

 (3) Open the flip-lock clamp (10) that attaches the harness (5) to the

 bracket. R R BEFORE SPIB NO. CFM02255MW1 R
 (4) Open the line blocks (15), (20), and (25) that attach the harness (5) to the brackets at station 158.

 (5) If necessary, remove the rubber supports from the line blocks.

 (6) Remove the harness (5) from the rubber supports and the flip-lock clamp (10).

 CONFIG-1

 (7) Open the line block (30) that attaches the harness (5) to the bracket at station 167 (B2).

 CONFIG-2
 (Ref. Fig. 406/TASK 71-51-43-991-311)
 (Detail B)

 F 『 EEFF : ALL E Page 46471-51-43
 E E Feb 01/04 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (8) Remove the bolt (55) that attaches the clamp (60) to the bracket at station 167. Remove the clamp (60) from the harness (5).

 END CONFIG-2

 (9) Open the line blocks (25), (40), (45) and (50) that attach the
 harness (5) to the brackets.
 (Ref. Fig. 407/TASK 71-51-43-991-312)

 (10) If necessary, remove the rubber supports from the line blocks.

 (11) Remove the harness (15) from the rubber supports.

 (12) Open the flip-lock clamp (35) near the ignition exciter A and remove the harness (5).

 AFTER SPIB NO. CFM02255MW1
 (Ref. Fig. 406/TASK 71-51-43-991-311)

 (13) Open the line block (25) that attaches the harness (5) to the bracket at station 158.

 (14) If necessary, remove the rubber supports fromm the line block.

 (15) Remove the bolts and clamps (17) that attach the harness (5) to the bracket at station 158.

 (16) Remove the bolts and clamps (22) that attach the harness (5) to the bracket at station 158.

 (17) Remove the harness (5) from the rubber supports, the flip-lock clamp

 (10) and the clamps (17) and (22).
 CONFIG-1

 (18) Open the line block (30) that attaches the harness (5) to the bracket at station 167 (B2).

 CONFIG-2
 (Ref. Fig. 406/TASK 71-51-43-991-311)
 (Detail B)

 (19) Remove the bolt (55) that attaches the clamp (60) to the bracket at station 167. Remove the clamp (60) from the harness (5).

 END CONFIG-2
 F 『 EEFF : ALL E Page 46571-51-43
 E E May 01/04 ERE
ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E E 56-5B E E E

R R  ECU Channel A Harness - Upper Right Fan Zone Figure 406/TASK 71-51-43-991-311- 12 (SHEET 1)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 466 Feb 01/04

R R  ECU Channel A Harness - Upper Right Fan Zone Figure 406/TASK 71-51-43-991-311- 22 (SHEET 2)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 467 Feb 01/04

R R  ECU Channel A Harness - Lower Right Fan Zone Figure 407/TASK 71-51-43-991-312- 12 (SHEET 1)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 468 Feb 01/04

R R  ECU Channel A Harness - Lower Right Fan Zone Figure 407/TASK 71-51-43-991-312- 22 (SHEET 2)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 469 Feb 01/04

 F  『
 E  C F M  E
 E  E

 (20) Open the line blocks (25), (40), (45) and (50) that attach the
 harness (5) to the brackets.
 (Ref. Fig. 407/TASK 71-51-43-991-312)

 (21) If necessary, remove the rubber supports from the line blocks.

 (22) Remove the harness (5) from the rubber supports.

 (23) Remove the bolt, clamp and anti-rotation lug (37) near the ignition exciter A and remove the harness (5).

 END SPIB NO. CFM02255MW1

 (24) Disconnect the electrical connector 4000JH1-A from the ignition
 exciter A.

 (25) Disconnect the electrical connectors 4000KS-J1 and 4000KS-J3 from the ECU.

 (26) Remove the electrical harness (5) from the engine.

 (27) Put protective covers on the electrical connectors.

 F 『 EEFF : ALL E Page 47071-51-43
 E E May 01/04 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 71-51-43-400-046
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(32)