INTENTIONALLY BLANK

 F 『R E E Page 44571-51-43
 E E Feb 01/04 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E (7) Remove the clamp (50) from the harness (5). Loosely install the bolt

R R  Lower Right Fan Zone Electrical Harness Figure 405/TASK 71-51-43-991-304- 14 (SHEET 1)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 446 Feb 01/04

R R  Lower Right Fan Zone Electrical Harness Figure 405/TASK 71-51-43-991-304- 24 (SHEET 2)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 447 Feb 01/04

R R  Lower Right Fan Zone Electrical Harness Figure 405/TASK 71-51-43-991-304- 34 (SHEET 3)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 448 Feb 01/04

R R  Lower Right Fan Zone Electrical Harness Figure 405/TASK 71-51-43-991-304- 44 (SHEET 4)
 F EEFF : E E ECES  ALL  『E 71-51-43EEE Page 449 Feb 01/04

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (45) in the clamp (75).
 END CONFIG-2
 (8) If necessary, remove the rubber supports from the line blocks and remove the harness (5) from the rubber supports.

 (9) Remove the harness (5) from the flip-lock clamps.

 (10) Remove the nuts (60), the lockwasher (65) and the washer (70) that attach the ground wires to the ground studs. (Ref. Fig. 404/TASK 71-51-43-991-303)
 WIRE GROUND
 GD9965DC/1 GD9965DC GD9965DC/2 GD9965DC GD9966DC/1 GD9966DC GD9966DC/2 GD9966DC GD9967DC/1 GD9967DC GD9968DC/1 GD9968DC GD9969DC/1 GD9969DC GD9970DC/1 GD9970DC GD9970DC/2 GD9970DC
 (11) Disconnect the electrical connector 4000DN-A from the anti-ice valve. (Ref. Fig. 405/TASK 71-51-43-991-304)

 (12) Disconnect the electrical connector 4001VC-A from the interphone jack disconnect at the inlet cowl aft bulkhead.

 (13) Open the three line blocks (35) attached to the brackets at station

 158.

 (14) Open the two flip top clamps (30) that attach the harness (5) to the brackets forward of the ECU at station 158.

 (15) If necessary, remove the rubber supports from the line blocks (60).

 (16) Remove the harness (5) from the rubber supports and the flip-lock

 clamps (30). R R AFTER SPIB NO. CFM02255MW1 R (Ref. Fig. 404/TASK 71-51-43-991-303) R
 F 『 EEFF : ALL E Page 45071-51-43
 E E Feb 01/04 E E ECES ER (17) Open the flip-lock clamps (10) that attach the harness (5) to the R engine brackets.

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E 

R (18) Remove the bolts and clamps (17) and (27), and the bolts, clamps and R anti-rotation lugs (32) that attach the harness (5) to the engine R brackets.
R (19) Remove the bolts and clamps (57), and the bolts, clamps and R anti-rotation lugs (59) that attach the harness (5) to the engine R brackets.
R (20) Remove the bolts and clamps (22) that attach the harness (5) to the R engine bracket.
R (21) Open the line blocks (35) attached to the brackets at station 158. R R CONFIG-1 R
R (22) Open the line block (40) that attaches the harness (5) to the bracket R at station 167. R R CONFIG-2 R (Ref. Fig. 404/TASK 71-51-43-991-303) R (DETAIL B) R
R (23) Remove the bolt (45) that attaches the clamps (50) and (75) to the R bracket at station 167.
R (24) Remove the clamp (50) to the harness (5). Loosely install the bolt R (45) in the clamp (75). R R END CONFIG-1 R
R (25) If necessary, remove the rubber supports from the line block and R remove the harness (5) from the rubber supports.
R (26) Remove the harness (5) from the flip-lock clamps.
R (27) Remove the nuts (60), the lockwasher (65) and the washer (70) that R attach the ground wires to the ground studs.
R (28) Disconnect the electrical connector 4000DN-A from the anti-ice valve. R (Ref. Fig. 405/TASK 71-51-43-991-304)
 F 『 EEFF : ALL E Page 45171-51-43
 E E Feb 01/04 E E ECES E F 『 EEFF : ALL E Page 45271-51-43

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E 

R  (29) Disconnect the electrical connector 4000DN-A from the interphone jack 
R  disconnect at the inlet cowl aft bulkhead. 
R  (30) Open the three line blocks (35) attached to the brackets at station 
R  158. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(27)