(1) Disconnect the electrical connector 457VC-A from the core junction box.

 (2) Remove the two bolts (5) and open the two clamps (10) that attach the harnesses to the pylon. Remove the harness 4206KS from the clamps. Install the bolt (5) and tighten it with your hand.

 (3) Remove the bolt (15) and open the clamp (20) that attaches the harness assemblies to the bracket at station 233. Remove harness 4206KS from the clamp. Install the bolt (15) and tighten it with your hand.

 (4) Remove the bolt (15) and open the clamp (35) that attaches the harness assemblies to the bracket at the top left side of the engine. Remove harness 4206KS from the clamp. Install the bolt (15) and tighten it with your hand.

 (5) Remove the bolts (15) and the clamp (40) that attaches the harness 4206KS to the bracket at station 221.

 F 『 EEFF : ALL E Page 45771-52-43
 E E May 01/05 ERE
ECES E F 『 E C F M E E E

 E 56-5B E

 Vibration Sensor Harness Assembly
 Figure 403/TASK 71-52-43-991-306- 12 (SHEET 1)

 F 『R EEFF : 001-049, 051-099, 101-149, 151-155, E Page 45871-52-43
 E E157-199, 201-299, 301-399, 401-499, Aug 01/05 E E ECES E F 『 E C F M E E E

 E 56-5B E

 Vibration Sensor Harness Assembly
 Figure 403/TASK 71-52-43-991-306- 22 (SHEET 2)

 F 『R EEFF : 001-049, 051-099, 101-149, 151-155, E Page 45971-52-43
 E E157-199, 201-299, 301-399, 401-499, Aug 01/05 E E ECES E F 『 E C F M E E E E 56-5B E

R Vibration Sensor Harness Assembly Figure 403A/TASK 71-52-43-991-306-A12 (SHEET 1)
 F 『R EEFF : 156-156, E Page 46071-52-43
 E E Nov 01/03 E E ECES E F 『 E C F M E E E E 56-5B E

R Vibration Sensor Harness Assembly Figure 403A/TASK 71-52-43-991-306-A22 (SHEET 2)
 F 『R EEFF : 156-156, E Page 46171-52-43
 E E Nov 01/03 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (6) Cut the lacing tape that attaches the thermal blanket (30) and remove the harness from the thermal blanket (30).

 (7) If necessary, remove the thermal blanket (25).

 (8) Disconnect the electrical connector 4003EV-A from the TRF vibration sensor.

 (9) Remove the harness assembly 4206KS from the engine.

 (10) Put blanking caps on the electrical connectors.
 F 『R EEFF : 156-156, E Page 46271-52-43
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 **ON A/C ALL

 TASK 71-52-43-400-044
 Installation of the Vibration Sensor Harness Assembly (4206KS)
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
 No specific access platform 1.5 m (4 ft. 11 in.) R No specific Torque Wrench : range 5.00 to 35.00 lbf.in R (0.05 to 0.40 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2208 USA 3M-361
 fiberglass adhesive tape (Ref. 70-30-00)
 Material No. CP8003 *
 lacing and tying tape (Ref. 70-30-00)

 F 『 EEFF : ALL E Page 46371-52-43
 E E May 01/05 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
 from the External Power
 31-60-00-860-001 EIS Start Procedure
 31-60-00-860-002 EIS Stop Procedure
 71-13-00-010-040 Opening of the Fan Cowl Doors
 71-13-00-410-040 Closing of the Fan Cowl Doors
 78-30-00-081-041 Make the Thrust Reverser Serviceable after

 Maintenance
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(88)