F 『
E C F M E
E E
E 56-5B E
E E
R (44) Remove the nuts (60), lockwashers (65) and washers (70) that attach
R the ground wires to the ground studs at station 191.
R (Ref. Fig. 414/TASK 71-51-43-991-308)
R WIRE GROUND
R
R GD9951DC/1 GD9951DC
R GD9951DC/2 GD9951DC
R GD9952DC/1 GD9952DC
R GD9952DC/2 GD9952DC
R GD9953DC/1 GD9953DC
R GD9953DC/2 GD9953DC
R GD9954DC/1 GD9954DC
R GD9954DC/2 GD9954DC
R GD9955DC GD9955DC
R GD9956DC GD9956DC
R GD9957DC GD9957DC
R (45) Remove the bolt, clamps and anti-rotation lug (57) that attach the
R harness (5) to the bracket at station 167.
R (Ref. Fig. 414/TASK 71-51-43-991-308)
R (46) Remove the bolts, clamps and anti-rotation lugs (43) that attach the
R harness (5) to the bracket at station 158.
R (47) Remove the bolts and clamp (33) that attach the harness (5) to the
R bracket at the station 158.
R (48) Disconnect the electrical connector 1074GK-A or 3074GD-A, as
R applicable, from the hydraulic pressure caution switch and remove the
R harness (5).
R (49) Open the flip-lock clamp (30) and remove the harness (5).
R (50) Remove the nuts (60), lockwashers (65) and washers (70) that attach
R the ground wires to the ground studs at station 158.
R (Ref. Fig. 414/TASK 71-51-43-991-308)
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
R WIRE GROUND
R
R GD9958DC/1 GD9958DC
R GD9958DC/2 GD9958DC
R GD9959DC/1 GD9959DC
R GD9959DC/2 GD9959DC
R GD9960DC/1 GD9960DC
R GD9960DC/2 GD9960DC
R GD9961DC/1 GD9961DC
R GD9961DC/2 GD9961DC
R GD9962DC/1 GD9962DC
R GD9962DC/2 GD9962DC
R GD9963DC/1 GD9963DC
R GD9963DC/2 GD9963DC
R GD9964DC GD9964DC
R (51) Disconnect the electrical connector 4007EN-A from the oil chip
R detector.
R (Ref. Fig. 415/TASK 71-51-43-991-309)
R (52) Disconnect the electrical connector 4002EN-A from the oil quantity
R transmitter.
R (53) Open the line blocks (40) and (55) that attach the harness (5) to the
R brackets at station 199.
R (54) Remove the bolt, clamps and anti-rotation lug (49) that attach the
R harness(5) to the bracket at station 199.
R (55) Open the line block (40) that attaches the harness (5) to the bracket
R at station 191.
R (56) If necessary, remove the rubber supports from the line blocks.
R (57) Remove the harness (5) from the rubber supports.
R (58) Remove the bolt (75) and clamp (80) that attach the harness (5) to
R the bracket at station 199.
R (59) Disconnect the electrical connector 4000KC-A from the high pressure
R fuel shutoff.
R (60) Open the line blocks (50) and (55) at station 158.
R (61) Remove the bolt, clamps and anti-rotation lug (58) that attach the
R harness (5) to the bracket at station 158.
F 『R EEFF : ALL E Page A45671-51-43
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(62) Remove the bolt and clamp (107) that attach the harness (5) to the bracket at station 158.
(63) Remove the harness (5) from the line blocks (50) and (55) rubber supports.
END SPIB NO. CFM02255MW1
(64) Remove the bolt (95) and the clamp (100) that attach the harness (5) to the bracket at station 158.
(65) Remove the bolt (75), the nut (85) and the clamp (90) that attach the harness (5) to the bracket on the gearbox.
(66) Disconnect the electrical connector 4004EN-A from the oil temperature sensor.
(67) Disconnect the electrical connector 4001EN-A from the oil differential pressure switch. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 2(55)
