R 1_ Place the "J" Ring Check Tool TBD (HIX3010-0) onto the "V"
R Blade of the "J" Ring.
R 2_ Check the gap between the tool and the forward face of the "V"
R blade using 0.010 in. (0.250 mm) thickness gauge. If it is
R greater than 0.010 in. (0.250 mm) replace the "J" Ring (Ref.
R CMM 78-32-35).
R 3_ Check the gap between the tool and the rear face of the "V"
R blade using 0.005 in. (0.125 mm) thickness gauge. If it is
R greater than 0.005 in. (0.125 mm) replace the "J" Ring (Ref.
R CMM 78-32-35).
F 『 EEFF : ALL E Page 62178-36-42
E E Feb 01/03 E E ECES E F 『 E C F M E E E E 56-5B E
R R Check "V" Outer Flange of "J" Ring with Tool Figure 606/TASK 78-36-42-991-322
F EEFF : E E ECES ALL 『E 78-36-42EEE Page 622 Feb 01/03
F 『
E C F M E
E E
E 56-5B E
E E
R Subtask 78-36-42-220-053
R D. Outer Flange Check
R (1) Damage less than the check tool length.
R NOTE : Only the damages under check tool length can be checked with
____ R check tool. A "V" groove clear area is necessary at each R extremity of the check tool.
R (a) Place the Outer Flange Check Tool TBD (HIX3011-0) into the "V"
R groove of the outer flange.
R (Ref. Fig. 607/TASK 78-36-42-991-323)
R 1_ Check the gap between the tool and the forward face of the "V"
R groove using 0.010 in. (0.250 mm) thickness gauge. If it is
R greater than 0.010 in. (0.250 mm), replace the adapter ring
R outer flange (Ref. TASK 78-36-42-000-001).
R NOTE : If more than three outer flanges are affected by half
____ R thrust reverser, replace the five outer flanges R (Ref. TASK 78-36-42-000-001).
R 2_ Check the gap between the tool and the rear face of the "V"R groove using 0.005 in. (0.125 mm) thickness gauge. If it is R greater than 0.005 in. (0.125 mm) replace the adapter ring R outer flange (Ref. TASK 78-36-42-000-001), or repair the R adapter ring outer flange (Ref. ESM 71-00-01).
R NOTE : If more than three outer flanges are affected by half
____ R thrust reverser, replace the five outer flanges R (Ref. TASK 78-36-42-000-001).
R 5. Close-up
________
R Subtask 78-36-42-410-062
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other R items.
R (2) Close the thrust reverser cowl doors: (Ref. TASK 78-36-00-410-040) R FOR 1000EM1 R 451AL, 452AR R FOR 1000EM2 R 461AL, 462AR
F 『 EEFF : ALL E Page 62378-36-42
E E Feb 01/03 E E ECES E F 『 E C F M E E E E 56-5B E
R R Check "V" Shape of the Outer Flange with Tool Figure 607/TASK 78-36-42-991-323
F EEFF : E E ECES ALL 『E 78-36-42EEE Page 624 Feb 01/03
F 『
E C F M E
E E
E 56-5B E
E E
R Subtask 78-36-42-440-056
R B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041)
R Subtask 78-36-42-410-063
R C. Close Access
R (1) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040) R FOR 1000EM1 R 437AL, 438AR R FOR 1000EM2 R 447AL, 448AR
R (2) Remove the access platform(s).
R (3) Remove the warning notice(s).
F 『 EEFF : ALL E Page 62578-36-42
E E Feb 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E E E ACTUATOR - COWL OPENING (3003KM1,3003KM2) - REMOVAL/INSTALLATION
________________________________________________________________
TASK 78-36-51-000-041
Removal of the Cowl Opening Actuator
WARNING : WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU
_______
WORK ON PRESSURIZED SYSTEMS.
R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______ R - FLUSH IT AWAY WITH CLEAN WATER R - GET MEDICAL AID.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(120)
