F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

_________
 (Ref. Fig. 601/TASK 78-32-41-991-312, 602/TASK 78-32-41-991-313, 603/TASK
 78-32-41-991-314)
 Subtask 78-32-41-210-051
 A. Do a visual inspection of the blocker door seal and the seal retainer as follows:
 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Examine the blocker door seal for:
 A. Damage  No damage permitted If you find some damage, replace the blocker door (Ref. TASK 78-32-41-000-001) or (Ref. TASK 78-32-41-000-002) and (Ref. TASK 78-32-41-400-001) or (Ref. TASK 78-32-41-400-002)
 B. Missing  No missing permitted If there is missing, replace the blocker door. (Ref. TASK 78-32-41-000-001) or (Ref. TASK 78-32-41-000-002) and (Ref. TASK 78-32-41-400-001) or (Ref. TASK 78-32-41-400-002)
 C. Cut  No fully through cut in If you find fully through the longitudinal cut in the longitudinal direction permitted direction, replace the
 blocker door (Ref. TASK 78-32-41-000-001) or (Ref. TASK 78-32-41-000-002) and (Ref. TASK 78-32-41-400-001) or (Ref. TASK 78-32-41-400-002)
 F 『 EEFF : ALL E Page 61378-32-41
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Door Seal and Permissible Damage of the Seals Retainer
 Figure 602/TASK 78-32-41-991-313

 F 『 EEFF : ALL E Page 61478-32-41
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Blocker door Seal and Permissible Damage of the Seal Retainer
 Figure 603/TASK 78-32-41-991-314

 F 『 EEFF : ALL E Page 61578-32-41
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
2. Examine the seal retainer for:
A. Gap
5. Close-up
________ Subtask 78-32-41-080-052
 Fully through cuts in the cross direction are permitted in these limits:
- 0.59 in. (15 mm) maximum length -Four cuts maximum per blocker door seal

- 3.93 in. (99.8 mm) minimum distance between two cuts

0.039 in. (1 mm) maximum gap between the seal
retainer and the seal If the fully through cutsare not in the serviceablelimits, replace theblocker door (Ref. TASK78-32-41-000-001) or(Ref. TASK 78-32-41-000-002)and (Ref. TASK 78-32-41-400-001) or (Ref. TASK 78-32-41-400-002).
If the gap is not in theserviceable limits,
reshape the seal retainer as follows : Apply a non metallic (i.e. wood, plastic) block on the area to be reshaped. Reshape the seal retainer using a wooden hammer through repeated soft actions.
 A. Remove the SAFETY SLEEVE - PIVOTING DOOR ACTUATOR (HIX3005) from the blocker door actuator without the thrust reverser operational (Ref. TASK 78-32-41-080-001).
 F 『 EEFF : ALL E Page 61678-32-41
 E E Feb 01/98 E E ECES E Subtask 78-32-41-410-062

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Stow the blocker door: CAUTION : BLOCKER DOOR LATCH MUST BE OPENED WHEN YOU CLOSE THE

_______
 BLOCKER DOOR OR DAMAGE CAN OCCUR.

 (a) Move the blocker door to the stow position manually (Ref. TASK 78-32-41-860-002).
 Subtask 78-32-41-820-052
 C. Make sure of the alignment of the blocker door (Ref. TASK 78-32-41-820-001).
 Subtask 78-32-41-440-053
 D. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041). Subtask 78-32-41-410-054
 E. Close Access
 (1) Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Remove the access platform(s).

 (3) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 61778-32-41
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 78-32-41-210-042
 General Visual Inspection of the Blocker Door Seals
 1. Reason for the Job
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(78)