R No specific Torque Wrench : range 5.00 to 35.00 lbf.in R (0.05 to 0.40 m.daN) No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN)
No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
F 『 EEFF : ALL E Page A45578-31-49
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. CP2245 *
finish paint EA4 blue 5991 (Ref. 70-30-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
R 10 packing 78-31-49 01A-260 R 20 packing 78-31-49 01A-220
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
78-31-49-991-319 Fig. 418
3. Job Set-up
__________
Subtask 78-31-49-860-098
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
F 『 EEFF : ALL E Page A45678-31-49
E E Aug 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(3) Make sure that the access platform is in position.
Subtask 78-31-49-010-154
B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
Subtask 78-31-49-040-143
C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
4. Procedure
_________
(Ref. Fig. 418/TASK 78-31-49-991-319)
Subtask 78-31-49-420-089
A. Installation of the Upper Swivel Joint:
(1) Installation of the Upper Rod Swivel Joint
(a) Remove the protective covers from the pipe ends. R (b) Lubricate the packing (20) with thrust reverser hydraulic fluid.
(c) Install the packing (20) on the fixed end of the rod swivel joint.
(d) Install the swivel joint onto the rod supply junction pipe.
(e) TORQUE the swivel joint to between 260 and 300 lbf.in (2.93 and
3.39 m.daN).
(f) Connect the upper rod supply hose to the swivel joint.
(g) TORQUE the coupling nut to between 130 and 150 lbf.in (1.46 and
1.69 m.daN).
NOTE : Apply a witness line of finish paint EA4 blue 5991
____ (Material No. CP2245) on all nuts and connections after they are torqued.
F 『 EEFF : ALL E Page A45778-31-49
E E Aug 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(2) Installation of the Upper Head Swivel Joint
(a) Remove the protective covers from the pipe ends. R (b) Lubricate the packing (10) with thrust reverser hydraulic fluid.
(c) Install the packing (10) on the fixed end of the head swivel joint.
(d) Install the swivel joint onto the head supply junction pipe.
(e) TORQUE the swivel joint to between 370 and 410 lbf.in (4.18 and
4.63 m.daN).
(f) Connect the upper head supply hose to the swivel joint.
(g) TORQUE the coupling nut to between 235 and 260 lbf.in (2.65 and 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM EXHAUST 2(6)
