(5) Cleaning of remaining sealant.
WARNING : BEFORE THE USE OF SOLVENT, PROTECTIVE FILM OR SEALANT
_______ CAREFULLY READ THE APPLICABLE "MATERIAL SAFETY DATA SHEET" AND FOLLOW ALL LISTED SAFETY AND HEALTH PRECAUTIONS. USE THESE PRODUCTS IN AN AREA OPENED TO THE AIR AND WEAR PROTECTION GLOVES. THESE PRODUCTS ARE FLAMMABLE AND VAPOR IS DANGEROUS. THEY MAY CAUSE IRRITATION OF EYES, NOSE, THROAT AND SKIN. HIGH CONCENTRATIONS MAY CAUSE WEAKNESS, HEADACHE, NAUSEA, DIZZINESS AND IMPAIRED JUDGEMENT.
R (a) Clean remaining sealant from the pylon surfaces with acetone
R (Material No. CP1039) or stoddard solvent (Material No. CP2011)
R or ardrox 552 (Material No. CP2559) or turco ind 79 (Material No.
R CP2560) or mag-chem teksol (Material No. CP2566) or degreasol 99R
R (Material No. CP2584) or mag-chem skysol (Material No. CP2656) or
R isopropyl alcohol (Material No. CP1041).
(b) Clean remaining sealant from the upper rear fairing and the hinge access panel bracket with acetone (Material No. CP1039) or isopropyl alcohol (Material No. CP1041).
(6) Dry the surfaces with a cloth before the solvent evaporates.
F 『 EEFF : ALL E Page 41878-32-42
E E May 01/05 E E ECES E F 『 E C F M E E E E 56-5B E
Upper Rear Fairing
Figure 403/TASK 78-32-42-991-307
F 『 EEFF : ALL E Page 41978-32-42
E E May 01/05 ERE
ECES E TASK 78-32-42-400-002
F 『
E C F M E
E E
E 56-5B E
E E
Installation of the Upper Rear Fairing
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific access platform 1 m (3 ft. 3 in.) No specific Torque Wrench : range 30 to 40 lbf.in
(0.33 to 0.45 m.daN) No specific Torque Wrench : range 35 to 45 lbf.in
(0.39 to 0.50 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP1039
Material No. CP1041
R Material No. CP2011
R
Material No. CP2243
Material No. CP2245
R Material No. CP2559
R
R Material No. CP2560
R
R Material No. CP2566
R
R Material No. CP2584
R
F
EEFF : ALL
E
E
ECES
*
acetone (Ref. 70-30-00)
*
isopropyl alcohol (Ref. 70-30-00)
*
stoddard solvent (Ref. 70-30-00)
*
PR1750 class B2 (Ref. 70-30-00)
*
finish paint EA4 Blue 5991 (Ref. 70-30-00)
*
ardrox 552 (Ref. 70-30-00)
*
turco ind 79 (Ref. 70-30-00)
*
mag-chem teksol (Ref. 70-30-00)
*
degreasol 99 R (Ref. 70-30-00)
『
E 78-32-42Page 420
E May 01/05EE -------------------------------------------------------------------------------
F 『
E C F M E
E E
E 56-5B E
E E
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R Material No. CP2656 *
R mag-chem skysol (Ref. 70-30-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
78-32-42-991-307 Fig. 403
3. Job Set-up
__________
Subtask 78-32-42-869-050
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2). 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(85)
