(2) Connect the lower head supply hose to the lower head swivel joint.

 (3) Connect the lower head supply hose to the lower hydraulic actuator.

 (4) TORQUE the coupling nuts to between 235 and 260 lbf.in (2.65 and 2.93 m.daN).

 (5) Attach the lower head shield to the forward frame with the bolts and nuts.

 (6) TORQUE the nuts to between 61 and 70 lbf.in (0.68 and 0.79 m.daN). NOTE : Apply a witness line of finish paint EA4 blue 5991 (Material

____ No. CP2245) on all nuts and connections after they are torqued.
 5. Close-up
________
 Subtask 78-31-49-440-099

 A. Make the thrust reverser serviceable: (Ref. TASK 78-30-00-081-041).
 Subtask 78-31-49-410-113

 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the access platform(s).

 F 『 EEFF : ALL E Page B40378-31-49
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (4) Remove the warning notice(s).

 Subtask 78-31-49-710-078
 C. Bleed the air from the thrust reverser hydraulic system. (Ref. TASK 78-30-00-710-040)
 F 『 EEFF : ALL E Page B40478-31-49
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 78-31-49-000-009
 Removal of the Lower Rod Supply Hose
 WARNING : WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU
_______
 WORK ON PRESSURIZED SYSTEMS.

R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______ R - FLUSH IT AWAY WITH CLEAN WATER R - GET MEDICAL AID.
 CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______
 ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE
 COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 1 USgal (4 L)
 No specific protective covers
 No specific warning notice
 No specific access platform 1 m (3 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance
 78-31-49-991-326 Fig. 425

 F 『 EEFF : ALL E Page B40578-31-49
 E E May 01/05 E E ECES E E 56-5B E

 F  『
 E  C F M  E
 E  E

 E E

 3. Job Set-up
__________ Subtask 78-31-49-941-099
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 78-31-49-010-136
 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Put the access platform in position. Subtask 78-31-49-040-124
 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041)
 F 『 EEFF : ALL E Page B40678-31-49
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E

 4. Procedure
_________ (Ref. Fig. 425/TASK 78-31-49-991-326) Subtask 78-31-49-020-096
 A. Removal of the Lower Rod Supply Hose
 (1) Put a container 1 USgal (4 L) under the lower hydraulic actuator to catch drained fluid.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM EXHAUST 2(19)