(b) TORQUE the bolts to between 70 and 80 lbf.in (0.79 and 0.90 m.daN).

 (18) Install the clevis access door on the blocker door:
 (Ref. Fig. 402/TASK 78-32-41-991-304)

 (a) Attach the clevis access door to the upper blocker door with the eight screws.
 F 『 EEFF : ALL E Page 42578-32-41
 E E Aug 01/03 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 (b) TORQUE the screws to between 35 and 45 lbf.in (0.39 and 0.50 m.daN).
 (19) Install the deploy-switch access door:
 (Ref. Fig. 403/TASK 78-32-41-991-307)

 (a) Attach the deploy-switch access door with the three screws.

 (b) TORQUE the screws to between 35 and 45 lbf.in (0.39 and 0.50 m.daN).

 (20) Stow the blocker door:

 CAUTION : BLOCKER DOOR LATCH MUST BE OPENED WHEN YOU CLOSE THE
_______
 BLOCKER DOOR OR DAMAGE CAN OCCUR.

 (a) Manually move the blocker door to the closed position (Ref. TASK 78-32-41-860-002).
 (21) Make sure that the blocker door is correctly aligned (Ref. TASK 78-32-41-820-001).
 5. Close-up
________
 Subtask 78-32-41-440-056
 A. Make thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 Subtask 78-32-41-410-057
 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowls doors (Ref. TASK 71-13-00-410-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR

 (3) Remove the access platform(s).

 (4) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 42678-32-41
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 TASK 78-32-41-000-003 Removal of the Latch Fitting and Latch Back Plate
 1. Reason for the Job

__________________
 Self Explanatory

 2. Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific access platform 1 m (3 ft. 3 in.) HIX3005 1 SAFETY SLEEVE - PIVOTING DOOR ACTUATOR
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 78-30-00-481-041 Make the Thrust Reverser Unserviceable for Maintenance 78-32-41-480-001 Installation of the Safety Sleeve on Blocker Door
 Actuator 78-32-41-860-001 Manual Deployment of the Blocker Door 78-32-41-991-315 Fig. 407
 3. Job Set-up
__________ Subtask 78-32-41-941-057
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 F 『 EEFF : ALL E Page 42778-32-41
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 78-32-41-010-057
 B. Get Access
 (1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Put an access platform in position. Subtask 78-32-41-040-057
 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 4. Procedure
_________ (Ref. Fig. 407/TASK 78-32-41-991-315) Subtask 78-32-41-020-052
 A. Removal of the latch Fitting and Latch Back Plate
 (1) Manually move the blocker door to the open position (Ref. TASK 78-32-41-860-001).

 (2) Install the SAFETY SLEEVE - PIVOTING DOOR ACTUATOR (HIX3005) on the blocker door (Ref. TASK 78-32-41-480-001).

 (3) Remove bolts, washers and nuts which attach the latch fitting.

 (4) Remove the latch fitting.

 (5) Remove the roller:

 (a) Remove and discard the cotter pin.

 (b) Remove the nut, washer and the roller bolt.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(69)