R Terminal Lugs - Stripping and Crimping Tools DAN387 Plug Figure 011

20-48-14 Page 1920-48-14 Page 2020-48-14 Page 21

R  (b) Extraction
R  _1  Only for ABS0374B: 
R  - Engage AMP tool 724659-1 at the rear of terminal and push 
R  up. 
R  - Extract the housing and the tool from the terminal.
R  _2  Only for DAN387-02:
 - Engage a screwdriver under the terminal at the front, and
 push up. 
R  - Then pull lightly on the cable to remove the terminal from 
R  the housing. 
R  (5) Installation/Removal of the terminal 
R  (Ref. Fig. 007)

R  ________________________________7. E0256 Clip terminal with housing
 A. P/N Identification
R R R R R R R R R  (1) Terminal E0256 C 1 B N 1 | | | | | | | | | | | --------- Packaging code | 0 = in strip | | | | | | 1 = in bulk | | | | ------------- Nickel plated | | | ----------------- Brass | | --------------------- Size code | ----------------------- Type code : C = Terminal ----------------------------- Standard P/N
R R R R R R R  (2) Sleeve E0256 M 1 A 1 | | | | | | | | | -------------- White colored | | | ------------------ Self-extinguishing material | | ---------------------- Size code | ------------------------ Type code : M = Housing ------------------------------ Standard P/N
 B. P/N Characteristics
 (1) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F) Maximum operating temperature is 105 deg.C (221.00 deg.F)
 ____NOTE : If this terminal is not available, you can replace it by DAN387 with related tools.
R  C. Connection Procedure (Ref. Fig. 012)
R  (1) Wire stripping Strip the wire to the length A with the applicable tool.
R  (2) Crimping procedure (Ref. Fig. 004, 005) - Make sure that the tool is adjusted correctly. - Hold the tool by the fixed handle with the crimping head up. - Push the operating lever out to increase the gap between the barrel and the indenter. - Engage the terminal into the tool and release the lever.

R Terminal Lugs - Stripping, Insertion and Crimping Tools E0256
R Figure 012

20-48-14 Page 2220-48-14 Page 23

 ____NOTE : Lightly close the rear tabs of the terminal with your fingers to get a better position of the terminal in the indenter.
 - Pull the lever in to engage the ratchet in the first notch. - Engage the wire into the rear part of the terminal and make sure that it is in the correct position for crimping.
 ____NOTE : For Gauge 24 wires, fold the conductor in the middle of the stripped length
 ____NOTE : For Gauge 24 and Gauge 22 wires, put the wire to one side (not in the middle) of the rear part of the terminal.
 - Fully close the tool handles until the ratchet releases. - Release the mobile handle and push the lever to release the terminal. 
R R R (3) Insertion/Extraction of the housing (E0256M) (Ref. Fig. 006) - Put the rear part of the protection sleeve(large hole)in front of the terminal. - Manually engage the terminal into the sleeve (for a terminal crimped with a Gauge 24 wire, the operation is easier if you use a CANNON CK1 tool). 
R R R  (4) Insertion/Extraction of the terminal - Push to insert the terminal and pull to extract it.

 ___________________________________________________
MISCELLANEOUS TERMINALS - DESCRIPTION AND OPERATION
 _______1. General
 Miscellaneous terminals installed on aircraft have the following code: 
R  - E0296 ground pick-up terminal 
R  - ABS0593 spring spade terminal 
R  - DAN417 non-insulated terminal
 NSA936502 non-insulated TB terminal
R  ______________________________2. E0296 Ground Pick-Up Terminals 
R 
R  A. P/N identification
 E0296 -01
 | |
 | -------- Reference Designator
 |
 ---------------- Standard P/N 
R 
R  B. P/N characteristics 
R  (Ref. Fig. 001)
 Used with E0295 connector.
R  _____________________________3. ABS0593 Spring Spade Terminal 
R 
R  A. P/N identification
 ABS0593 -01
 | |
 | -------- Size Code
 |
 ------------------- Standard P/N 
R 
R  B. P/N characteristics 
R 
R  (Ref. Fig. 002) 
R 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(23)