曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  pull-back braid 
R  (Ref. Fig. 011, 013) 
R  - Step 1: Clean the area using ASN42202 cleaning product and a little 
R  brush. 
R  Cut the external protection (if installed) to 210 mm (8.2677 in.) 
R  and the overbraid 180 mm (7.0866 in.) from the backshell. 
R  - Step 2: Fold back the overbraid on the shells, 200 mm (7.8740 in.) 
R  from the backshell. 
R  - Step 3: Install the braid ABS1353-005 to replace the removed 
R  pull-back braid. 
R  Crimp the braid ABS1353-005 on the half shells ABS0940 with a 
R  metallic clamping strip E0805-2. 
R  Protect the cutting edges of the metallic clamping strip adding 5 
R  layers of self-welding tape ABS5334. 
R  - Step 4: Install the modification kits through the braid ABS1353-005 
R  along the internal protection. (Make sure that the first kit is 
R  installed 150 mm (5.9055 in.) from the backshell and the other kits 
R  staggered every 25 mm (0.9842 in.)). 
R  - Step 5: Crimp the metallic clamping strip E0805-2, the bonding 
R  leads and the braid ABS1353-005 at the rear of the backshell. 
R  Secure the modification kits with lacing tape NSA8420-7. 
R  - Step 6: Wrap with self-welding tape ABS5334. 
R  Protect the cutting edges of the metallic clamping strip doing 5 
R  turns of the tape over the same position at the rear of the 
R  backshell. 
R  - Step 7: Do the same process (step 1 to step 6) for the other side 
R  of the harness to connect the other end of the modification kit. 
R  (8) Repair type 2-H - Insulation of the damaged cables 
R  (Ref. Fig. 014, 015) 
R  - Step 1: Clean the area using ASN42202 cleaning product and a little 
R  brush. 
R  Cut the external protection (if installed), the overbraid and the 
R  internal protection in the damaged area. 
R  - Step 2: Install two half shells ABS0940 and fold back the overbraid 
R  on the shells 30 mm (1.1811 in.) each side of the damaged area. 
R  Cut the damaged cables and isolate them with shrink sleeves ABS0916 
R  crushed at the end. 
R  - Step 3: Wrap with 2 layers of self-welding tape ABS5334 (overlap 
R  50% and 30 mm (1.1811 in.) each side of the damaged area). 
R  - Step 4: Install the split conduit EN6049-008 over the damaged area. 
R  - Step 5: Crimp the split conduit with metallic clamping strip 
R  E0805-2 at the center level of the half shells. 
R  - Step 6: Wrap the damaged area with 2 layers of self-welding tape 
R  ABS5334 (overlap 50% and 30 mm (1.1811 in.) each side over the 
R  external protection).

 

R Repair of Metallic Conduits - Modification Kit Installation R Repair Type 2-G R Figure 013

20-53-32 Page 18

R Repair of Metallic Conduits - Damaged Cables Repair Procedure R Repair Type 2-H R Figure 014

20-53-32 Page 19

R Repair of Metallic Conduits - Damaged Cables Repair Procedure R Repair Type 2-H R Figure 015

20-53-32 Page 2020-53-32 Page 21

R  (9) Repair type 2-J - Modification kit adjonction 
R  (Ref. Fig. 016, 017) 
R  - Step 1: Clean the area using ASN42202 cleaning product and a little 
R  brush. 
R  Remove the external protection (if installed). 
R  Pull back the overbraid to a length of 150 mm (5.9055 in.) 
R  - Step 2: Install the modification kit through the overbraid along 
R  the internal protection. 
R  Insert a shrink sleeve NSA937210 on the wire of the modification 
R  kit, at the passing through level. 
R  Install the bonding lead outside or inside the overbraid (inside is 
R  preferable if there is enough space). 
R  - Step 3: Push the overbraid against the backshell and crimp with a 
R  metallic clamping strip E0805-2 (the bonding lead must be crimped 
R  together with the overbraid). 
R  Install the external protection (if any) on the overbraid. 
R  Install the lacing tapes NSA8420-7 to secure the modification kit 
R  on the harnesses (not necessary at the level of the new external 
R  protection). 
R  - Step 4: Do the same process (step 1 to step 3) for the other side 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(85)