曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  | ABS1381 | ABS1343 | ABS1427 | 
R  ---------------------------------------------------------------------
R  B. Contact Insertion/Extraction Tools 
R  (Ref. Fig. 002) 
R  C. Wire Stripping 
R  (Ref. Fig. 003, 004) 
R  - Before stripping, put a colored mark on the wire. 
R  (1) For wire gauges 08 to 04 only: 
R  - Slide the sleeves E0718, NSA937502 and if necessary, a sealing 
R  sleeve (e.g. ABS0992) on the wire before stripping. 
R  - Strip the wire to the length A. 
R  - Make sure that the stripped wire is circular before you put it on 
R  the contact to prevent damage on the internal o-ring gasket.

 

R Normal Contacts - P/N Characteristics R ABS1380 and ABS1381 R Figure 001

20-48-24 Page 2

R Normal Contacts - Insertion/Extraction Tools R ABS1380 and ABS1381 R Figure 002

20-48-24 Page 3

R Normal Contacts - Wire Stripping and Tools R ABS1380 and ABS1381 R Figure 003

20-48-24 Page 4

R Normal Contacts - Wire Stripping R ABS1380 and ABS1381 R Figure 004

20-48-24 Page 520-48-24 Page 6

R  D. Insulation procedure 
R  (Ref. Fig. 003) 
R  (1) For wire gauges 08 to 04 only: 
R  (Ref. Fig. 004) 
R  - Slide the sleeve E0718 until it is level with the stripped wire and 
R  shrink it. 
R  - Shrink the sleeve NSA937502 at the rear and on the sleeve E0718. 
R  - Make sure that the sealing sleeve (e.g ABS0992) is installed before 
R  crimping. 
R  E. Crimping Procedure 
R  (Ref. Fig. 005, 006) 
R  - Make sure that the sleeve E0718 (if installed) is shrunk on the wire. 
R  - Engage the stripped wire in the contact (for gauges 08 to 04 only, use 
R  lubricant HELLERINE or equivalent on the end of the sleeve). 
R  - Install the contact in the positioner. 
R  - Select the applicable tool. 
R  - Install the contact in the positioner. 
R  - Fully close the tool handles until the safety ratchet releases. 
R  - Remove the crimped contact. 
R  - Make sure that the contact crimping is correct. 
R  - Make sure that the length C (colored mark) is correct. 
R  - If installed, slide the sealing sleeve on the contact.

 

R Normal Contacts - Crimping Tools R ABS1380 and ABS1381 R Figure 005

20-48-24 Page 7

R Normal Contacts - Crimping Tools R ABS1380 and ABS1381 R Figure 006

20-48-24 Page 820-48-24 Page 9

R  _________________________________________________________________________3. Connection Procedure for Contacts E0445, E0446, EN3155-004 and EN3155-005 
R  A. Contact P/N and Characteristics 
R  (Ref. Fig. 007) 
R  ---------------------------------------------------------------------
R  | | USE WITH | 
R  | CONTACT |------------------------------------------------| 
R  | | PLUG | RECEPTACLE | 
R  |------------------|-------------------------|----------------------| 
R  | E0445 | E0441 | | 
R  | E0446 | E0442 | E0444 | 
R  | EN3155-004 | EN2997 | EN2997 | 
R  | EN3155-005 | | | 
R  ---------------------------------------------------------------------
R  B. Temperature 
R  Minimum operating temperature is -65 deg.C (-85.00 deg.F). 
R  Maximum operating temperature is 260 deg.C (500.00 deg.F). 
R  C. Contact Insertion/Extraction Tools 
R  (Ref. Fig. 008) 
R  D. Wire Stripping 
R  (1) Normal wires 
R  (Ref. Fig. 009, 010, 011) 
R  - If necessary install the heat shrinkable sleeve on the wire before 
R  stripping. 
R  Shrinking is done after crimping. 
R  - Use the applicable tool. 
R  - Strip the wire to the length "A". 
R  (2) Special wires 
R  (Ref. Fig. 009) 
R  E0437 DL22 and DL20 
R  NSA935132 DJ20 
R  - Remove the fiberglass braid then the PTFE envelope along a length 
R  of 50 mm (1.9685 in.). 
R  - Strip the core cable along a length of 35 mm (1.3779 in.). 
R  - Install the heat shrinkable sleeve NSA937210MB0200 on the outer 
R  sheath along 10 mm (0.3937 in.) and shrink. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(35)