R Locking Procedure for Circular Connectors - Typical Lockwiring Procedure Figure 002

20-51-12 Page 320-51-12 Page 4

R  - Insert the wire end through the appropriate hole (Ref. STEP 3). 
R  - Twist the lockwire with the locking pliers at a distance of 15 mm 
R  (0.5905 in.) (Ref. STEP 4). 
R  - Cut the excessive length (Ref. STEP 5). 
R  - Bend back the part of the lockwire that is out (Ref. STEP 6).
 - Check that the connector is correctly safetied. 
R 
R  (4) Example of Lockwiring 
R  Miscellaneous lockwiring cases exit, some of them are given in the 
R  following figures.
 (Ref. Fig. 003, 004)

R Locking Procedure for Circular Connectors - Examples of Lockwiring Figure 003

20-51-12 Page 5

R Locking Procedure for Circular Connectors - Examples of Lockwiring Figure 004

20-51-12 Page 620-51-12 Page 7

R  B. Locking With an Adhesive Product procedure 
R  (1) Material 
R  Adhesive (Mat. No. 08-048). 
R  (2) Procedure 
R 
R  - Apply the adhesive product on the screwed part of the connector. 
R  - Screw the connector on the connecting part. 
R  - Remove the excess adhesive product.
R  ______________________3. Locking Type Selection 
R  The locking type to be applied or not depends on the connector type. 
R  Refer to the following figures to select the locking type to be applied. 
R
 (Ref. Fig. 005, 006, 007, 008, 009, 010, 011, 012) 
R

R Locking Procedure for Circular Connectors - Locking Type Selection R Pressure Seal E0073
 Figure 005

20-51-12 Page 8

R Locking Procedure for Circular Connectors - Locking Type Selection R Connector NAS1599 and Derivative (Screw Locking)
 Figure 006

20-51-12 Page 9

R Locking Procedure for Circular Connectors - Locking Type Selection R Connector NSA1599 and Derivative (Bayonet Locking) Figure 007

20-51-12 Page 10

R Locking Procedure for Circular Connectors - Locking Type Selection R Connector MIL-C-5015 R Figure 008

20-51-12 Page 11

R Locking Procedure for Circular Connectors - Locking Type Selection R Connector MIL-C-83723 (Screw Locking) R Figure 009

20-51-12 Page 12

R Locking Procedure for Circular Connectors - Locking Type Selection R Connector EN2997 R Figure 010

20-51-12 Page 13

R Locking Procedure for Circular Connectors - Locking Type Selection R Connector NSA938027 and NSA938028 (MIL-C-38999) R Figure 011

20-51-12 Page 14

R Locking Procedure for Circular Connectors - Locking Type Selection R ABS0327
 Figure 012

20-51-12 Page 15

 _________________________________________________________________
LOCKING PROCEDURE FOR TERMINAL BLOCKS - DESCRIPTION AND OPERATION
 _______
1. General This chapter gives the method used to lock terminal blocks at the end clamps. This process must be applied on all the terminal block end clamps located in the vibration areas.
R __________________2. Standard Procedure
 A. Lockwiring procedure
 (1) Material Locking pliers Ref. BELZER VAN EXTRA 2855 or equivalent. Lockwire stainless steel 0.6 mm (0.0236 in.) dia. (Mat. 19-018). Lockwire 0.5 mm (0.0196 in.) (AMS 5687) (Mat. 19-009). Lockwire 0.8 mm (0.0314 in.) (Mat. 19-010).
 (2) Procedure R (Ref. Fig. 001, 002)
 -Install the end clamp on the rail.
 -Tighten the assembly with a screwdriver (no specific).
 -Insert the lockwire through the screw lockwire hole (Ref. STEP 1).
 -Twist the lockwire with the locking pliers at a sufficient length (Ref. STEP 2).
 -Insert the wire end through the appropriate hole (Ref. STEP 3).
 -Twist the lockwire with the locking pliers at a distance of 15 mm (0.5905 in.) (Ref. STEP 4).
 -Cut the excessive length of wire.
 -Bend back the part of the lockwire that is out (Ref. STEP 5).
 -Check that the end clamp is correctly safetied.

20-51-15 Page 1

 Locking Procedure for Terminal Blocks - End Clamp Lockwiring Procedure
 NSA937901-S
 Figure 001

20-51-15 Page 2

 Locking Procedure for Terminal Blocks - End Clamp Lockwiring Procedure
 NSA937901-S
 Figure 002

20-51-15 Page 320-51-30 Page 1

 _______________________________________________SOLDERING PROCESSES - DESCRIPTION AND OPERATION
 _______1. General
 This chapter gives the general processes for the repair or replacement of
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(57)