R (5) Method 2E
R (a) Cut the cable and wires.
R (b) Install the heat-shrink sleeve.
R (c) Install the two solder sleeves.
R (d) Install the splice insulation sleeve(s) and if applicable the
R adapters, on each wire.
R (e) Put one end of the splice in the applicable crimping tool die.
R (f) Hold the splice in the correct position with the positioner.
R (g) Put the stripped end of the wire in the splice barrel.
R (h) Crimp the splice (fully tighten the handle until the ratchet
R releases).
R (i) Remove the splice from the crimping tool.
R (j) Do the same operation for the other side of the splice from step
R (e).
R (k) Do a check to make sure that the splicing is correct.
R (l) Put the insulation sleeve in the correct position.
R (m) Install the sealing adapters under the sleeve (they must show out
R of the sleeve on a dimension of 0.80 mm (0.0314 in.)
R (n) Put one side of the insulation sleeve in the crimping die.
R (o) Crimp the sleeve (fully tighten the handle until the ratchet
R releases).
R (p) Remove the assembly from the crimping tool.
R (q) Do the same operation for the other end of the sleeve from step
R (l).
R (r) Do a check to make sure that the sleeves are in the correct
R position.
R (s) Do the same operation for the other wires of the cable from step
R (e) (the splices must be staggered).
R (t) Turn the solder sleeve when you engage it on the shielding link
R so that it does not catch on the strands.
R (u) Center the solder on the stripped portion of the bonding wire and
R shield.
R (v) Heat the center of the sleeve (do not turn the assembly when you
R do this) until the sleeve shrinks (the solder ring melts and
R flows into the strands of the bonding wire and shield).
R (w) Let cool for a few seconds.
R (x) Do the operation again for the other side from step (t).
R (y) Install the heat-shrink sleeve.
R (z) Shrink the sleeve.
R ____NOTE : PTFE requires a minimum temperature of 327 deg.C (620.60
R deg.F) for the shrinking. At level of the two solder
R sleeves, it is necessary to prevent overheat of the
R solder.
R (6) Method 2F
R (a) Cut the cable and wires.
R (b) Install the heat-shrink sleeve.
R (c) Install the two solder sleeves.
R (d) Install the screened sleeve.
R (e) Install the splice insulation sleeves and the adapters on each
R wire.
R (f) Put one end of the splice in the applicable crimping tool die.
R (g) Hold the splice on the correct position with the positioner.
R (h) Put the stripped end of the wire in the splice barrel.
R (i) Crimp the splice (fully tighten the handle until the ratchet
R releases).
R (j) Remove the splice from the crimping tool.
R (k) Do the same operation for the other side of the splice from step
R (f).
R (l) Do a check to make sure that the splicing is correct.
R (m) Put the insulation sleeve in the correct position.
R (n) Install the sealing adapters under the sleeve (they must show out
R of the sleeve on a dimension of 0.80 mm (0.0314 in.)
R (o) Put one side of the insulation sleeve in the crimping die.
R (p) Crimp the sleeve (fully tighten the handle until the ratchet
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(78)
