R Layout and Table for Damage Assessment R AD, ADB, ADC, ADD and ADE Figure 001
20-53-25 Page 2
R Layout and Table for Damage Assessment R VNA, VNB, VNC and VND R Figure 002
20-53-25 Page 3
R Layout and Table for Damage Assessment R VNA, VNB, VNC and VND R Figure 003
20-53-25 Page 4
R (b) 20-53-29 GENERAL REPAIR PROCEDURE for more data.
R C. Aluminum Feeder Cables
R (1) Cable Layout
R (Ref. Fig. 004)
R (2) Table for Damage Assessment
R (Ref. Fig. 004)
R (3) When the repair is selected, refer to:
R (a) Para. 3 Repair Procedure for the general description and
R conditions of application.
R (b) 20-53-29 GENERAL REPAIR PROCEDURE for more data.
R
20-53-25 Page 5
R Layout and Table for Damage Assessment QP, YU and YV
R Figure 004
20-53-25 Page 620-53-25 Page 7
R ________________3. Repair Procedure
R A. Procedure
R (Ref. Fig. 005, 006, 007, 008)
R This paragraph gives the general description and conditions of
R application for each repair type.
R (1) Method 2A or 4A - Wrapping with PTFE tape Material No 05-116
R Ref. 20-53-29 for detailled procedure.
R (2) Method 2B or 4B - Heat-Shrink Sleeve Insulating
R (3) Method 2C
R (a) Disconnect the cable end.
R (b) Install the heat-shrink sleeve.
R (c) Install the two solder sleeves.
R (d) Engage the solder sleeve on the cable and the shielding link
R (wire CF 22).
R (e) Turn the solder sleeve when you engage it on the bonding wire so
R that it does not catch the strands.
R (f) Center the solder on the stripped portion of the bonding wire and
R shield.
R (g) Heat the center of the sleeve (do not turn the assembly when you
R do this) until the sleeve shrinks (the solder ring melts and
R flows into the strands of the bonding wire and shield).
R (h) Let cool for a few seconds.
R (i) Do the operation again for the other side from step (d).
R (j) Install the heat-shrink sleeve.
R (k) Shrink the sleeve.
R ____NOTE : PTFE requires a minimum temperature of 327 deg.C (620.60
R deg.F) for the shrinking. At level of the two solder
R sleeves, it is necessary to prevent overheat of the
R solder.
R Repair of Unscreened Low-Temp Cables - Repair Procedure Table R VNA, VNB, VNC and VND R Figure 005
20-53-25 Page 8
R Repair of Unscreened Low-Temp Cables - Repair Procedure Table R VNA, VNB, VNC and VND R Figure 006
20-53-25 Page 9
R Repair of Aluminum Feeder Cables - Repair Procedure Table QP, YU and YV Figure 007
20-53-25 Page 10
R Repair of Aluminum Feeder Cables - Repair Procedure Table QP, YU and YV Figure 008
20-53-25 Page 1120-53-25 Page 1220-53-25 Page 1320-53-25 Page 1420-53-25 Page 1520-53-25 Page 16
R (4) Method 2D
R (a) Disconnect the cable end.
R (b) Install the heat-shrink sleeve.
R (c) Install the two solder sleeves.
R (d) Install the screened sleeve.
R (e) Turn the solder sleeve when you engage it on the screened sleeve
R so that it does not catch the strands.
R (f) Center the solder on the screened sleeve and shield.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(77)
