曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

0.00/+0.15 millimeters), adjust the aft support of the auxiliary track;
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-00
Page 528
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
1) Loosen the upper aft aux track locking bolt [91].
a) Loosen the nut [90].
2) Loosen the jam nut [82].
3) Loosen the nut [80] on the locking bolt [79].
4) Turn the adjusting nut [81] until the gap between the slat and the fixed leading edge is
0.0020 -0.0000/+0.0060 inch (0.05 -0.00/+0.15 millimeters).
5) Temporarily tighten the locking bolt [79].
6) Temporarily tighten the jam nut [82].
(f) Reduce the dimension A by 0.0210 ±0.0030 inch (0.53 ±0.08 millimeters) to preload the
slat trailing edge;
1) Loosen the jam nut [82].
2) Loosen the nut [80] to loosen the locking bolt [79].
3) Turn the adjusting nut [81] 180 ±30 degrees clockwise, viewed from below.
(g) Temporarily tighten the locking bolts [79].
(h) Temporarily tighten the jam nuts [82].
(i) Make sure the weighted average misfair is 0.0000-0.0500 inch (0.00-1.27 millimeters).
(j) Make sure the slat endstops touch the horizontal and vertical stop pads.
(k) If the slat endstops do not touch the horizontal and vertical stop pads, adjust the stop pad:
1) Remove the retainers [85], nuts [86] and bolts [89].
2) Add or remove shim [87] as it is necessary until the slat fairs with the adjacent slat.
NOTE: Add or remove only a minimum amount of shim necessary for the slat upstop
to touch the stop pad. To adjust each stop pad, add or subtract in any
combination of 0.0100, 0.0200, 0.0400,and 0.0630 inch thick solid shims. The
total permitted shim thickness is 0.0000 to 0.1280 inch and must be such that
the slat flex skin keeps solid contact with the fixed leading edge.
3) Install the bolts [89], nuts [86] and retainers [85].
(l) Measure and write down the misfairs at six locations for each of these gaps (Table 502);
1) The gap between all adjacent slat ends
2) The gap between the outboard end of slats 1 and 8 and the adjacent fixed leading edge
3) The gap between the inboard end of slats 4 and 5 and the adjacent fixed leading edge.
(m) Measure the slat end gap at three locations for each slat (Table 503).
Table 503/27-81-00-993-814
Point Location Value
G1 Outbd slat 1/8
G2 Outbd slat 1/8
G3 Outbd slat 1/8
G11 Inbd slat 1/8
G12 Inbd slat 1/8
G13 Inbd slat 1/8
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-00
Page 529
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(Continued)
Point Location Value
G21 Inbd slat 2/7
G22 Inbd slat 2/7
G23 Inbd slat 2/7
G31 Inbd slat 3/6
G32 Inbd slat 3/6
G33 Inbd slat 3/6
G41 Inbd slat 4/5
G42 Inbd slat 4/5
G43 Inbd slat 4/5
1) Make sure the gaps between all adjacent slat ends is 0.2600 -0.0600/+0.1500 inch (6.60
-1.52/+3.81 millimeters).
2) Make sure the gaps between the slat ends and the adjacent fixed leading edge is
0.2500 -0.0600/+0.1500 inch (6.35 -1.52/+3.81 millimeters).
SUBTASK 27-81-00-860-035
WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF THE LEADING EDGE FLAPS
AND SLATS AND THE TRAILING EDGE FLAPS. THE FLAPS AND SLATS CAN MOVE
QUICKLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(5) To extend the leading edge slats to the full extend (10-unit detent) position, do this task: Leading
Edge Flaps and Slats Extension, TASK 27-81-00-860-803.
SUBTASK 27-81-00-220-005
(6) Make sure the minimum gap at these locations is 0.2000 inch (5.08 millimeters);
(a) The gaps between all adjacent slat ends.
(b) The gaps between the outboard end of slats 1 and 8 and the adjacent fixed leading edge.
(c) The gaps between the inboard end of slats 4 and 5 and the adjacent fixed leading edge.
SUBTASK 27-81-00-860-086
(7) To extend the leading edge slats to the (intermediate) extend (1-unit detent) position, do this
task: Leading Edge Flaps and Slats Extension, TASK 27-81-00-860-803.
SUBTASK 27-81-00-820-012
(8) Make sure the detent roller touch the root of each detent arm.
NOTE: You may manually apply load to the slats to help the slats meet the requirement.
SUBTASK 27-81-00-820-013
(9) Align the noses of the slats to get a mismatch of 0.0000 to 0.0600 inch (0.00 to 1.52 millimeters)
between the adjacent slats.
(a) Measure the gap between the detent roller and the aft surface of the cam plate.
(b) Make sure the sum of all of the gaps is 0.000 to 0.060 inch (0.00 to 1.52 millimeters).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(51)