曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Removal, TASK 29-11-00-860-805.
------------------------- END OF TASK ---------------------------
TASK 27-81-61-860-802
5. Flap and Slat Hydraulic Fuse (Standby System) Reset
A. References
Reference Title
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
B. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
C. Procedure
SUBTASK 27-81-61-860-005
(1) Do these steps to reset the hydraulic fuse for the standby system:
(a) Make sure the flap control lever is in the UP position.
(b) Remove power from hydraulic sytems B. To remove power from hydraulic system B, do
this task: Hydraulic System A or B Power Removal, TASK 29-11-00-860-805.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-61
Page 406
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
LEADING EDGE FLAP FLOW LIMITING VALVE - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the leading edge flap flow limiting valve
(2) An installation of the leading edge flap flow limiting valve.
B. The leading edge flap flow limiting valve is referred to as the "flow limiting valve" in this procedure.
TASK 27-81-71-000-801
2. Leading Edge Flap Flow Limiting Valve Removal
(Figure 401)
A. References
Reference Title
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
32-00-01-480-801 Landing Gear Downlock Pins Installation (P/B 201)
B. Location Zones
Zone Area
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
C. Prepare for the Removal
SUBTASK 27-81-71-480-001
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEAR.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR COULD RETRACT AND CAUSE
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) If the downlock pins are not installed on all the landing gear, do this task: Landing Gear
Downlock Pins Installation, TASK 32-00-01-480-801.
SUBTASK 27-81-71-860-001
(2) Make sure there is no hydraulic power on system B. To remove power from hydraulic system B,
do this task: Hydraulic System A or B Power Removal, TASK 29-11-00-860-805.
D. Leading Edge Flap Flow Limiting Valve Removal
SUBTASK 27-81-71-020-001
(1) Remove the flow limiting valve [1]:
(a) Loosen the nuts [3] and [4] to disconnect the hydraulic tubes from the flow limiting valve [1]
and the hydraulic fuse [2].
(b) Remove the flow limiting valve [1] from the hydraulic fuse [2].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-71
Page 401
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Flap Flow Limiting Valve Installation
Figure 401 (Sheet 1 of 2)/27-81-71-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-71
Page 402
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Flap Flow Limiting Valve Installation
Figure 401 (Sheet 2 of 2)/27-81-71-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-71
Page 403
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-81-71-400-801
3. Leading Edge Flap Flow Limiting Valve Installation
(Figure 401)
A. References
Reference Title
12-12-00-610-801 Hydraulic Reservoir Servicing (P/B 301)
24-22-00-860-811 Supply Electrical Power (P/B 201)
29-11-00-860-801 Hydraulic System A or B Pressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
B. Location Zones
Zone Area
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
C. Leading Edge Flap Flow Limiting Valve Installation
SUBTASK 27-81-71-420-001
(1) Install the flow limiting valve [1]:
(a) Connect the flow limiting valve [1] to the hydraulic fuse [2].
(b) Hold the flow limiting valve [1] and hydraulic fuse [2] in their position.
NOTE: The flow direction arrow on the flow limiting valve [1] and hydraulic fuse [2] must
agree with the arrow on the pressure bulkhead.
(c) Connect the hydraulic tubes to the flow limiting valve [1] and hydraulic fuse [2].
(d) Tighten the nuts [3] and [4].
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(93)