曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

TO EQUIPMENT.
(18) Remove the lockout set, SPL-1734 from the actuator of the leading edge flap. To do this, do this
task: Leading Edge Flap and Slat Locks Removal, TASK 27-81-00-080-801.
SUBTASK 27-81-11-860-009
WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF THE LEADING EDGE FLAPS
AND SLATS AND THE TRAILING EDGE FLAPS. THE LEADING EDGE FLAPS AND
SLATS AND THE TRAILING EDGE FLAPS CAN MOVE QUICKLY. THIS CAN CAUSE
INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(19) Move the flap control lever to the FLAP UP detent to retract the leading edge flaps.
SUBTASK 27-81-11-860-010
(20) Do a check of the flap panel clearances.
(a) For all but the aft 5 inches (127 millimeters) of the flap, make sure the gap between the
inboard Leading edge flap [1] and the outboard Leading edge flap [2] is 0.060-0.150 inch
(1.52-3.81 millimeters).
(b) For the aft 5 inches of the flap, make sure the gap between the inboard Leading edge flap [1]
and the outboard Leading edge flap [2] is 0.060-0.250 inch (1.5-6.4 millimeters).
SUBTASK 27-81-11-210-002
(21) If the flap panel clearances are out of tolerance, do a check of the wing and flap panel for
damage or warpage.
NOTE: This check is to make sure that the flap and the wing align correctly. There is no
adjustment that you can do.
SUBTASK 27-81-11-860-011
(22) To remove power from hydraulic system B, do this task: Hydraulic System A or B Power
Removal, TASK 29-11-00-860-805.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-11
Page 420
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Gap/Misfair Measurement
Figure 402 (Sheet 1 of 4)/27-81-11-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-11
Page 421
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Gap/Misfair Measurement
Figure 402 (Sheet 2 of 4)/27-81-11-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-11
Page 422
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Gap/Misfair Measurement
Figure 402 (Sheet 3 of 4)/27-81-11-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-11
Page 423
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Gap/Misfair Measurement
Figure 402 (Sheet 4 of 4)/27-81-11-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-11
Page 424
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
LEADING EDGE FLAP - INSPECTION/CHECK
1. General
A. This procedure contains the task to do an inspection of the leading edge flap.
TASK 27-81-11-200-801
2. Leading Edge Flap Inspection
(Figure 601)
A. General
(1) This task gives wear limits and repair data for the leading edge flap inspection.
B. References
Reference Title
27-81-11-000-801 Leading Edge Flap Removal (P/B 401)
27-81-11-400-801 Leading Edge Flap Installation (P/B 401)
C. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
STD-1097 Caliper - Vernier, 0-6 Inch, Readable to 1/1000 Inch
D. Location Zones
Zone Area
512 Left Wing - Krueger Flap No. 2
513 Left Wing - Krueger Flap No. 1
612 Right Wing - Krueger Flap No. 3
613 Right Wing - Krueger Flap No. 4
E. Procedure
SUBTASK 27-81-11-020-004
(1) Do this task: Leading Edge Flap Removal, TASK 27-81-11-000-801.
SUBTASK 27-81-11-020-005
(2) Use these tools to do a check for wear on the parts of the leading edge flap:
(a) micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096
(b) readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
SUBTASK 27-81-11-020-006
(3) Examine the parts of the leading edge flap for worn areas:
(a) Remove the parts you want to do a check.
(b) Measure the parts with a micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096 or a
readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
(c) Compare the dimensions you measured with the permitted wear dimensions.
(d) If the parts are out of tolerance, replace or repair the part if it is necessary.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(67)