曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

SUBTASK 27-81-31-860-003
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LEADING EDGE
FLAPS AND SLATS AND THE TRAILING EDGE FLAPS. THE FLAPS AND SLATS WILL
EXTEND. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
CAUTION: MAKE SURE THE INBOARD FAN DUCT COWL AND THE INBOARD AND OUTBOARD
THRUST REVERSERS ARE CLOSED OR REMOVED BEFORE YOU EXTEND THE
LEADING EDGE FLAPS AND SLATS. THERE IS NOT SUFFICIENT CLEARANCE FOR
THE FLAPS AND SLATS TO EXTEND IF THE INBOARD FAN DUCT COWL AND THE
INBOARD AND OUTBOARD THRUST REVERSERS ARE IN THE OPEN POSITION. THIS
CAN CAUSE DAMAGE TO EQUIPMENT.
(3) Move the flap control lever to the 1-unit detent to extend the leading edge flaps.
SUBTASK 27-81-31-480-001
WARNING: CAREFULLY INSTALL THE LEADING EDGE FLAP ACTUATOR LOCK TO PREVENT
ACCIDENTAL OPERATION OF THE LEADING EDGE FLAPS. THE LEADING EDGE
FLAPS CAN MOVE QUICKLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE
TO EQUIPMENT.
(4) Install the lockout set, SPL-1734 on the actuator for adjacent leading edge flap. To install the lock,
do this task: Leading Edge Flap and Slat Locks Installation, TASK 27-81-00-480-801.
E. Leading Edge Flap Actuator Removal
SUBTASK 27-81-31-020-001
(1) Disconnect the applicable actuator [11] or [12] from the leading edge flap:
(a) Remove the pin [19], nut [24], washer [23], washer [22], bushing [21], washer [20] and bolt
[18] that attach the actuator [11] to the No. 1 leading edge flap [1].
(b) Remove the pin [26], nut [30], washer [29], washer [22], bushing [28], washer [27] and bolt
[25] that attach the actuator [12] to the No. 2 leading edge flap [2].
SUBTASK 27-81-31-860-004
(2) Move the flap control lever to the UP detent to retract the applicable actuator [11] or [12].
SUBTASK 27-81-31-860-005
(3) To remove power from hydraulic system B, do this task: Hydraulic System A or B Power
Removal, TASK 29-11-00-860-805.
SUBTASK 27-81-31-020-002
(4) Remove the leading edge flap actuator [11] or [12]:
(a) Disconnect the three hydraulic lines [4], [9] and [10]:
1) Remove the screws [6], nuts [7] and clamps [5] that attach the hydraulic line [4] to the
bracket [8].
2) Disconnect the hydraulic lines [4], [9] and [10] from the hydraulic fittings [3].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-31
Page 402
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
3) Install the plugs in the hydraulic lines [4], [9] and [10].
4) Install caps in the hydraulic fittings [3].
(b) Remove the nut [17], washer [16], washer [14], bolt [13] and bushing [15] that attach the
actuator [11] or [12] to the structure.
(c) Remove the actuator [11] or [12].
NOTE: Remove the hydraulic lines [4], [9] and [10] with the actuator [11] or [12].
SUBTASK 27-81-31-020-003
(5) If you will install a new actuator [11] or [12], remove the hydraulic lines [4], [9] and [10]:
(a) Remove the hydraulic lines [4], [9] and [10] from the actuator [11] or [12].
(b) Install the plugs in the ends of the hydraulic lines [4], [9] and [10].
(c) Install caps in the hydraulic ports on the actuator [11] or [12].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-31
Page 403
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Flap Actuator Installation
Figure 401 (Sheet 1 of 3)/27-81-31-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-31
Page 404
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Flap Actuator Installation
Figure 401 (Sheet 2 of 3)/27-81-31-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-31
Page 405
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Leading Edge Flap Actuator Installation
Figure 401 (Sheet 3 of 3)/27-81-31-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-31
Page 406
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-81-31-400-801
3. Leading Edge Flap Actuator Installation
(Figure 401)
A. References
Reference Title
27-81-00-080-801 Leading Edge Flap and Slat Locks Removal (P/B 201)
27-81-00-700-802 Leading Edge Flap and Slat Timing Test in Primary Mode (P/B 501)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(78)