曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Set lights to BRIGHT or DIM as appropriate.
Fuel Quantity Indicators (Flow) ...................................................CHECKED
BCD Verify the fuel CONFIG indication extinguished.
>>@ Qty Test Switch (Flow) ................................................PRESS
Note: Do not test while aircraft is being refueled.
Press and hold until the fuel quantity indicators drive to zero and ERR is
displayed.
Releasing the test switch initiates a self-test. The fuel quantity indicators
should display the following:
· Error code for approximately two seconds.
· 8s for approximately two seconds.
· Maximum fuel tank capacity for up to two seconds.
· Actual fuel quantity.
Fuel Flow Switch (Flow)........................................................................RESET
Engine Instruments (Flow)........................................................... CHECKED
>>@ Press engine oil quantity test button and verify both indicators
move toward zero and return to the original setting when the switch is
released.
Verify the oil quantity is sufficient for dispatch.
Scan RPM, EGT, fuel flow, oil pressure and oil temperature gauges for
normal indications. Press N1 reference knobs in to permit FMC control of
N1 bugs.
BCD Check N1 and N2 zero, EGT, F/F, oil pressure, and oil
temperature pointers and digital readouts are not displayed until the start
switch is moved to GRD.
BCD Engine Display Control Panel (Flow) .....................................SET
N1 SET selector ..................................................................................AUTO
Permits FMC control of N1 bugs.
Speed Reference selector ...................................................................AUTO
Permits FMC control of reference speed bugs.
Sec. 3 Page 52 737
Rev. 11/15/02 #41 Continental Flight Manual
>>@ Anti-Skid Control Switch (Flow) ....................................CAPPED
Verify that the anti-skid switch is capped and the warning light is
extinguished.
BCD Anti-Skid INOP Light (Flow) ......................... EXTINGUISHED
Autobrake (Flow)....................................................................................... RTO
Verify AUTOBRAKE DISARM light illuminates and then extinguishes after 2
seconds.
Radar (Flow) ........................................................................ CHECKED, OFF
Prior to Weather Radar Test Procedures, the IRS alignment must be
complete.
Weather Radar Test Procedures:
On > with the Bendix RDR-4B-2457 Radar:
Set the radar system control as follows:
Mode selector .......................................................................................TEST
Antenna stab ............................................................................................ ON
Gain.....................................................................................................AUTO
Range Control.........................................................................ANY RANGE
Brightness ...............................................................................AS DESIRED
Check the display for:
· The presence of green, yellow, and red bands with three pie-shaped
magenta areas.
· Appearance of alphanumeric legends (cues).
If there is any fault in the system, there will be no test pattern.
Note: If the MSG button is depressed, the screen will display NO AUX DATA.
Depressing the MSG button again will restore the previous display.
On Non-EFIS -300 with the Bendix RDR-4B-3459 Radar:
· Mode Selector ...............................................................................TEST
· Gain.............................................................................................AUTO
· Range.................................................................................................. 40
· Brightness........................................................................AS DESIRED
Note: In addition to the normal Test Pattern display check for the
Caution, W/S Fail, W/S Warning and the Aural annunciations.
737 Sec. 3 Page 53
Flight Manual Continental Rev. 11/15/02 #41
On >@BCD aircraft test the radar as follows:
Either EHSI any expanded scale mode except PLAN
· Select any mode except TEST on the WXR control panel.
· Turn the WXR on using the EFIS WXR on button
· Select TEST on the WXR control panel and observe results.
Verify no fault messages present.
§ Select Mode selector (WXR switch) OFF at the end of the test.
Note: The WXR will radiate following step 2 until the WXR is
selected step 4 (at most a few seconds). The safe distance is
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 FLIGHT MANUAL 737飛行手冊1(115)