(a)
 Remove and discard the cotter pin (140). Remove the nut (139), the washer (138) and the screw (136).

 (b)
 Disconnect the rod (135) from the support (137).

 (c)
 Remove the nut (130) and the washer (131).

 (d)
 Hold the casing (134) in position. Remove the screw (133) and the washer (132).

 (e)
 Release and remove the screw (141). Remove and discard the lockwasher (142).

 (f)
 Lift the casing (134) and disengage it from the screw (143). Remove the casing (134).

 (7)
 Remove the upper arm (Ref. Fig. 405/TASK 32-21-27-991-003)

 (a)
 Release and remove the nut (71). Remove the washer (72).

 (b)
 Remove the screw (74) with a soft drift.

 (c)
 Remove the upper shaft (73) with the EXTRACTOR (J47563).

 (d)
 Remove the washers (69) and (70).

 (e)
 Remove the upper arm from the torque links.

 (f)
 Retain the support assy

 1_ Remove and discard the cotter pins (67). Remove the nuts (68)
 and the washers (66).
 2_ Remove the screws (62), the washers (63) and the stop (64).
 3_ Remove the screw (60) and the washer (61).
 4_  Remove the support (65).

R 1EFF : 001-004, 052-054, 106-149, 229-299, 1 32-21-27Page 410 1303-399, 401-499, 1Aug 01/05 1 1 1CES 1

 Nose Gear Torque Links - Target Support
 Figure 404/TASK 32-21-27-991-005

R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 32-21-27Page 411 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

R  Nose Gear Torque Links - Target Support 
R  Figure 404A/TASK 32-21-27-991-005-A 
R 1EFF :  051-051,  1  32-21-27 Page 412 
1  1  May 01/05
 1  1
 1CES  1

 Nose Gear Torque Links - Upper Hinge
 Figure 405/TASK 32-21-27-991-003

R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 32-21-27Page 413 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 005-049, 055-099, 101-105, 151-199, 201-228, 301-302,

 Subtask 32-21-27-020-055-A
 A. Removal of the Torque Link Assy
 (1)
 Disconnect the center hinge
 (Ref. Fig. 402/TASK 32-21-27-991-001)

 (a)
 Remove the cotter pin (9) from the nut (8).

 (b)
 Remove the nut (8), the washer (7) and the screw (10).

 (c)
 Hold the shaft (1) and remove the nut (6) and the washer (5).

 (d)
 Remove the shaft (1) with a plastic drift.

 (e)
 Remove the washers (4), (3) and (2).

 (2)
 Remove the lower arm
 (Ref. Fig. 403A/TASK 32-21-27-991-002-A)

 (a)
 Remove and discard the cotter pin (29).

 (b)
 Remove the nut (30) and the support (28).

 (c)
 Remove the screw (22) with a soft drift.

 (d)
 Remove the lower shaft (31) with the EXTRACTOR (J47563).

 (e)
 Remove the lower arm of the torque links and the washers (20) and (21).

 (f)
 Remove the nuts (23), the washers (24), the bolts (27) and the washers (26). Remove the stop (25).

 (3)
 Remove the target support
 (Ref. Fig. 404/TASK 32-21-27-991-005)

 (a)
 Remove and discard the cotter pin (140). Remove the nut (139), the washer (138) and the screw (136).

 (b)
 Disconnect the rod (135) from the support (137).

 (c)
 Remove the nut (130) and the washer (131).

R 1EFF : 005-049, 055-099, 101-105, 151-199, 1 32-21-27Page 414 1201-228, 301-302, 1May 01/05 1 1 1CES 1

 (d) Hold the casing (134) in position. Remove the screw (133) and the washer (132).
 (e) Release and remove the screw (141). Remove and discard the lockwasher (142).
 (f) Lift the casing (134) and disengage it from the screw (143). Remove the casing (134).
 (4) Remove the upper arm (Ref. Fig. 405/TASK 32-21-27-991-003)
 (a) Release and remove the nut (71). Remove the washer (72).
 (b) Remove the screw (74) with a soft drift.
 (c) Remove the upper shaft (73) with the EXTRACTOR (J47563).
 (d) Remove the washers (69) and (70).
 (e) Remove the upper arm from the torque links.
 (f) Retain the support assy
 1_ Remove and discard the cotter pins (67). Remove the nuts (68) and the washers (66).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(109)