(1) Close the MLG doors to the fully closed position with the Uplock locked.(Ref. TASK 32-12-00-410-001).
 NOTE : Make sure that green hydraulic system is depressurized
____
 1EFF : ALL 1 32-12-11Page 410 1 1 Feb 01/04 1 1 1CES 1

 Main Gear Doors (Z734/Z744) - Adjustment Figure 402/TASK 32-12-11-991-003
 1EFF : 1 1R 1CES  ALL  1 11 1 32-12-11 Page 411 Nov 01/00

 (2) Measure the gap between the door and the airframes. (Ref. Fig. 403/TASK 32-12-11-991-002) The correct gap is from A to B 4.5 +3.5 -2.5 mm (0.1771 +0.1377 -0.0984 in.) and at C 8.5 +2.25 -2.25 mm (0.3346 +0.0885 -0.0885 in.). If the gap is not correct, adjust on the hinge attachment point.
 (a)
 Open the MLG door (Ref. TASK 32-12-00-010-001).

 (b)
 Remove and discard the cotter pin (1).

 (c)
 Remove the nut (2), the washer (3) and the hinge bolt (6).

 (d)
 Adjust the position of the washer (5) between the spherical bearing (4) and the fitting (7).

 (e)
 Install the washer (5) so as to move the door forwards or rearwards.

 -
Position AA will move the door forwards.

 -
Position BB will move the door rearwards.

 (f)
 Install the hinge bolt (6), the washer (3) and the nut (2).

 (g)
 TORQUE the nut (2) to between 2.8 and 5.6 m.daN (20.64 and 41.29 lbf.ft).

R (h) Safety the nut (2) with a new cotter pin (1).
 Subtask 32-12-11-820-057-A
 F. Adjustment of the Door Stopper
 (Ref. Fig. 404/TASK 32-12-11-991-008)

 (1) Close the MLG doors to the fully closed position with the Uplock locked.(Ref. TASK 32-12-00-410-001).
 NOTE : Make sure that green hydraulic system is depressurized
____
 (2)
 Measure the step between the MLG door rear edge and the airframe structure .The door should make a continuous surface with the adjacent fairing structure.

 (3)
 A maximum step of 1.5 mm (0.0590 in.) inside of the adjacent fairing structure is permited.

 (4)
 It is also permitted a maximum step of 2.5 mm (0.0984 in.) inside of the adjacent structure on 305 mm (12.0078 in.) (10%) of the gap lenght (MLG door rear edge).

 1EFF : ALL 1 32-12-11Page 412 1 1 Feb 01/04 1 1 1CES 1

 Main Gear Doors (Z734/Z744) - Adjustment Figure 403/TASK 32-12-11-991-002
 1EFF : 1 1R 1CES  ALL  1 11 1 32-12-11 Page 413 Feb 01/01

 Main Gear Door (Z734/Z744) - Adjustment Figure 404/TASK 32-12-11-991-008 
R 1EFF : 1 1 1CES  ALL  1 111 32-12-11 Page 414 Feb 01/01

R R R R  (5) Measure the step between the MLG door rear edge and the airframe structure .The door should make a continuous surface with the adjacent fairing structure. A maximum step of 2.5 mm (0.0984 in.) out of the adjacent fairing structure is permited. 
R R R  (6) It is also permitted a maximum step of 5.0 mm (0.1968 in.) out of the adjacent structure on the last 80 mm (3.1496 in.) of the upper part (MLG door rear edge). 
R R  (7) Adjust the door stoppers assemblies if the step is greater than the maximum 
R  (a) Open the MLG door (Ref. TASK 32-12-00-010-001). 
R  (b) Remove the nuts (1), the washers (2) and the screws (6) 
R  (c) Remove the stop (5) and the plate (3). 
R  (d) Add or remove the plate set-packing as necessary. 
R R  (e) Install the stop (5) with the plate set-packing (4) and the plate (3) with the screws (6) the washers (2) and the nuts (1).
 Subtask 32-12-11-820-058
 G. Adjustment of the Uplock Roller (Ref. Fig. 405/TASK 32-12-11-991-005)
 (1) Close the MLG doors to the fully closed position with the Uplock locked.(Ref. TASK 32-12-00-410-001).
 NOTE : Make sure that green hydraulic system is depressurized____
 (2) Measure the step between the MLG door forward edge and the airframe structure. The door should make a continuous surface with the adjacent fairing structure. A maximum step of 2.5 mm (0.0984 in.) inside of the adjacent fairing sructure is permitted.
 (3) Measure the step between the MLG door forward edge and the airframe structure. The door should make a continuous surface with the adjacent fairing structure.
 (a) A maximum step of 1.5 mm (0.0590 in.) out of the adjacent fairing structure is permitted.

 1EFF : ALL 1 32-12-11Page 415 1 1 Feb 01/01 1 1 1CES 1

 Main Gear Door (Z734/744) - Adjustment Figure 405/TASK 32-12-11-991-005
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(26)