(2)
Put the warning notices in position to tell persons not to operate the hydraulic systems.
(3)
Put the access platform in position at zone 734 for the left hand main landing gear door and/or zone 744 for the right hand main landing gear door.
1EFF : ALL 1 32-12-11Page 402 1 1 Feb 01/99 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 401/TASK 32-12-11-991-001) Subtask 32-12-11-020-053
A. Disconnect Main Gear Door
(1)
Remove and discard the cotter pins (1), (10) and (23) from the nuts
(2) and (9).
(2)
Remove the nuts (9), the washers (8) and the screws (7), to disconnect the bonding leads (11).
(3)
Disconnect the actuator (13) 2523GM (2522GM) from the main gear door (Ref. TASK 32-31-35-000-001).
(4)
Remove the nuts (2) and the washers (3) from the hinge bolts (12) and (26).
Subtask 32-12-11-020-050
B. Remove Main Gear Door
(1)
Support the main gear door and remove the hinge bolts (12) and (26), and the washers (25), if installed.
(2)
Remove the spacers (4) and (24) and the bush (5).
(3)
Remove the main gear door and put it on a clean and dry surface.
1EFF : ALL 1 32-12-11Page 403 1 1 Feb 01/98 1 1 1CES 1
Main Gear Doors (Z734/Z744) - Removal/Installation
Figure 401/TASK 32-12-11-991-001- 12 (SHEET 1)
1EFF : ALL 1 32-12-11 Page 404
1 1 Feb 01/98
1 1
1CES 1
Main Gear Doors (Z734/Z744) - Removal/Installation
Figure 401/TASK 32-12-11-991-001- 22 (SHEET 2)
1EFF : ALL 1 32-12-11 Page 405
1 1 Feb 01/98
1 1
1CES 1
TASK 32-12-11-400-001 Installation of the Door Assembly - Main. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE ITEMS THEY
_______
OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) 98D32109005000 1 BULLET-MLG DOOR BOLT LOCATING
1EFF : ALL 1 32-12-11Page 406 1 1 May 01/05 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 09-004 D DA-2-657-4 SEALANT, AERODYNAMIC SMOOTHING-OBSOLETE USE 09016 (Ref. 20-31-00)
Material No. 16-003 F ASNB70720
COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
1 cotter pin 32-12-03 01D-030
R 1 cotter pin 32-12-03 01D-090
R 10 cotter pin 32-12-03 01D-130
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(24)
