3. Job Set-up
__________
 Subtask 32-21-00-941-061

 A. Safety Precaution
 (1)
 In the cockpit, on the panel 400VU, put the warning notice in position to tell persons not to operate the landing gear control lever.

 (2)
 Put the warning notices in position to tell persons not to operate the nose wheel steering system: - on the brake pedals - on the nose wheel steering handwheel (18VU, 19VU).

 4. Procedure
_________
 Subtask 32-21-00-020-050

 A. Removal of the NLG Towing Attachment
 (1)
 Remove the rubber sealant with a spatula to prevent damage to the surface protection.

 (2)
 Remove and discard the cotter pins (6).

 1EFF : ALL 1 32-21-00Page 401 1 1 Nov 01/03 1 1 1CES 1

 (3)
 Remove the nuts (5), the washers (3) and (4).

 (4)
 Remove the bolts (1) and the washers (2).

 (5)
 Remove the NLG towing attachment (7). NOTE : After towing attachement removal, do not reassemble the bolts,

____ nuts and washers, on the NLG leg.
 1EFF : ALL 1 32-21-00Page 402 1 1 May 01/03 1 1 1CES 1 TASK 32-21-00-440-001

 Reactivation of the NLG TOWING attachement (2701GM).
 1. Reason for the Job
__________________
 Refer to the CDL TASK: 32-3
 Nose Fitting Towing
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific  Torque Wrench : range 1.00 to 10.00 m.daN
 (8.00 to 75.00 lbf.ft)
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
Material No. 05-047  C Z-11.904
 ANTI COR. COMPOUND(HIGH TEMP.SILICONE SEALANT)
 (Ref. 20-31-00)

 Material No. 09-001  USA MIL-S-8802 TYPE I CLASS A
 FUEL TANK SEALANTPOLYSULFIDE (Ref. 20-31-00)

 Material No. 09-002  USA MIL-S-8802 TYPE I CLASS B
 FUEL TANK SEALANTPOLYSULFID(NO LONGER AVAILABLE
 (Ref. 20-31-00)

 Material No. 11-001  USA MIL-D-16791 TYPE I
 DETERGENT (Ref. 20-31-00)

 C. Expendable Parts
 -------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION  |IPC-CSN
 -------------------------------------------------------------------------------
R  6 cotter pins 32-21-13 03A-010 6 cotter pins 32-21-13 03B-010 6 cotter pins 32-21-13 03C-010
 1EFF : ALL 1 32-21-00Page 403 1 1 May 01/05 1 1 1CES 1

 3. Job Set-up
__________ Subtask 32-21-00-941-062
 A. Safety Precaution
 (1)
 In the cockpit, on the panel 400VU, make sure that the warning notice is in position to tell persons not to operate the landing gear control lever.

 (2)
 Make sure that the warning notices are in position to tell persons not to operate the nose wheel steering system: - on the brake pedals - on the nose wheel steering handwheel (18VU, 19VU).

 4. Procedure
_________ Subtask 32-21-00-420-050
 A. Installation of the NLG Towing Attachment
 (1)
 Clean the removed parts with CLEANING AGENTS (Material No. 11-001) and dry them with compressed air.

 (2)
 Apply a light coat of SPECIAL MATERIALS (Material No. 05-047) to the threads of the bolts (1).

 (3)
 Install the NLG towing attachment (7) on the leg.

 (4)
 Install the washers (2), the bolts (1), the washers (3) and (4) and the nuts (5).

 (5)
 TORQUE the nuts (5) to between 4.4 and 5.2 m.daN (32.44 and 38.34 lbf.ft).

 (6)
 Safety the nuts with new cotter pins (6).

 (7)
 Apply a layer of SEALANTS (Material No. 09-001) in the areas E.

 (8)
 Apply a layer of SEALANTS (Material No. 09-002) in the areas F.

 1EFF : ALL 1 32-21-00Page 404 1 1 May 01/03 1 1 1CES 1

 5. Close-up
________ Subtask 32-21-00-941-063
 A. Put the Aircraft in the Initial Configuration
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the warning notice(s).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(59)