(2)
Install the NLG aft doors (Ref. TASK 32-22-13-400-001).
1EFF : ALL 1 32-22-00Page 412 1 1 Aug 01/01R 1 1 1CES 1
5. Close-up
________ Subtask 32-22-00-860-060
A. Put the aircraft back to its initial configuration.
(1)
Remove the warning notice(s).
(2)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 32-22-00Page 413 1 1 Aug 01/01R 1 1 1CES 1
TASK 32-22-00-040-003 Preparation of the A/C for flight without NLG Leg Door Assy WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.
_______
WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE ITEMS THEY
_______ OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM.
1.
Reason for the Job
__________________
CDL 52-11
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-22-15-000-001 Removal of the Leg Door Assy 32-22-00-991-010 Fig. 403
3. Job Set-up
__________ Subtask 32-22-00-860-056
A. Safety Precautions
(1) Put the safety barriers in position.
1EFF : ALL 1 32-22-00Page 414 1 1 Aug 01/01R 1 1 1CES 1
4. Procedure
_________ (Ref. Fig. 403/TASK 32-22-00-991-010) Subtask 32-22-00-020-053
A. Removal of the NLG Leg Door
(1)
Remove the NLG leg door (Ref. TASK 32-22-15-000-001).
(2)
Remove all attaching parts from the door:
-Link assembly
-Fitting assembly
-Rod.
5. Close-up
________ Subtask 32-22-00-860-057
A. Put the aircraft back to its initial configuration.
(1)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 32-22-00Page 415 1 1 Aug 01/01R 1 1 1CES 1
NLG Leg Door Assy Figure 403/TASK 32-22-00-991-010
1EFF : 1 1R 1CES ALL 1 11 1 32-22-00 Page 416 Aug 01/01
TASK 32-22-00-440-003 Restoration of the A/C after flight without NLG Leg Door Assy
1.
Reason for the Job
__________________
CDL 52-11
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-22-15-400-001 Installation of the Leg Door Assy
3. Job Set-up
__________ Subtask 32-22-00-860-058
A. Safety Precautions
(1) Put the safety barriers in position.
4. Procedure
_________ Subtask 32-22-00-420-052
A. Installation of the NLG Leg Door
(1) Install the NLG leg door and all the attaching parts (Ref. TASK 32-22-15-400-001).
1EFF : ALL 1 32-22-00Page 417 1 1 Aug 01/01 1 1 1CES 1
5. Close-up
________ Subtask 32-22-00-860-059
A. Put the aircraft back to its initial configuration.
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(136)
