REFERENCE DESIGNATION
-------------------------------------------------------------------------------
**ON A/C 001-049, 051-061, 101-105, 201-203,
32-12-13-991-001 Fig. 401 R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
32-12-13-991-001-A Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
**ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 401/TASK 32-12-13-991-001) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 32-12-13-991-001-A)
**ON A/C ALL
Subtask 32-12-13-941-050
A. Safety Precautions
Put the safety barriers in position.
(1)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
(2)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in the cockpit to tell persons not to operate the landing gear.
1EFF : ALL 1 32-12-13Page 402 1 1 Aug 01/05 1 1 1CES 1
(3)
On panel 110VU, make sure that the GRAVITY GEAR EXTN handle is folded
into the center console.
(4)
Put a warning notice at the ground door opening panel, to tell persons not to operate the landing gear doors.
Subtask 32-12-13-869-052
B. Flight Configuration Precautions
(1)
If the electrical power is not necessary for other maintenance tasks, de-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002). Then, it is not necessary to operate the LGCIU circuit breakers.
(2)
If the electrical power is necessary, do the precautions for flight configuration (Ref. TASK 32-00-00-860-001) before you open the LGCIU circuit breakers.
Subtask 32-12-13-865-050
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
Subtask 32-12-13-010-053
D. Get Access
(1)
Put an access platform below the applicable zone:
-
for the left wing, below zone 733
-
for the right wing, below zone 743.
(2)
Remove the fixed fairing (Ref. TASK 32-12-14-000-001).
4. Procedure
_________ R **ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 401/TASK 32-12-13-991-001)
1EFF : ALL 1 32-12-13Page 403 1 1 May 01/05 1 1 1CES 1
Secondary Hinged Fairing Figure 401/TASK 32-12-13-991-001- 12 (SHEET 1)
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 32-12-13Page 404 1 1 May 01/05 1 1 1CES 1
Secondary Hinged Fairing Figure 401/TASK 32-12-13-991-001- 22 (SHEET 2)
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 32-12-13Page 405 1 1 May 01/05 1 1 1CES 1
Secondary Hinged Fairing
Figure 401A/TASK 32-12-13-991-001-A12 (SHEET 1)
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 32-12-13Page 406 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Secondary Hinged Fairing
Figure 401A/TASK 32-12-13-991-001-A22 (SHEET 2)
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 32-12-13Page 407 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 32-12-13-991-001-A)
**ON A/C ALL
Subtask 32-12-13-020-050
A. Removal of the Secondary Hinged Fairing CAUTION : HOLD THE SECONDARY HINGED FAIRING OR IT WILL BECOME DAMAGED.
_______
NOTE : If the same hinged fairing is to be installed, do not move the
____ actuating rod (3) locknuts or the hinged fairing adjustment will change.
(1)
Remove and discard the cotter pins (4) and (8).
(2)
Remove the nut (5), the bolt (7) and the bonding tag (6).
(3)
Remove the nuts (9) and the bolts (10).
(4) 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(30)
