R 1EFF : 051-099, 102-149, 151-199, 201-299, 1 32-12-14Page 443 1401-499, 1Aug 01/05 1 1 1CES 1
(12)
Turn the studs (20) on the rod-ends (28) until the shoulders of the studs (20) touch the support plates (19).
(13)
Install the outer serrated plates (16), the locking devices (14) and
(13) and the lock nuts (12).
(14)
Tighten the lock nuts (12) sufficiently to make sure that the serrated plates (16) do not disengage. However, make sure that you can turn the studs (20).
(15)
Make sure that the fixed fairing (1) steps and gaps are correct (refer to the dimensions above). If necessary use the spools (2) to adjust the MLG fixed fairing (1) to the correct position.
(16)
If necessary, adjust each stud (20) so that the stud shoulder touches the support plate (19).
(17) Tighten the lock nuts (12) sufficiently to make sure that the MLG R fixed fairing (1) is stable during MLG extension.
(18)
Extend the applicable MLG (Ref. TASK 32-30-00-867-002).
(19)
Make sure that the safety devices are on the appplicable MLG (Ref. TASK 32-00-00-481-001).
(20)
Turn the spools (2), the minimum amount, to align a slot with the thread holes in the fixed fairing (1).
(21)
Install the washers (4) and the bolts (5).
(22)
Remove the RIGGING SPACER from the bolts (27) at positions C and F.
(23)
Make sure that the dimensions Z and Y are correct. They must be between 1.3 mm (0.0511 in.) and 2.7 mm (0.1062 in.).
(24)
Check that the threads of the rod-ends (28) can be seen through the inspection holes in the studs (20).
(25)
TORQUE the bolts (5) to between 0.17 and 0.23 m.daN (15.04 and 20.35 lbf.in).
(26)
Safety the bolts (5) with MISCELLANEOUS (Material No. 19-010).
R 1EFF : 051-099, 102-149, 151-199, 201-299, 1 32-12-14Page 444 1401-499, 1Aug 01/05 1 1 1CES 1
R (27) TORQUE the lock nuts (12) to between 4.0 and 4.3 m.daN (29.49 and 31.71 lbf.ft).
R R NOTE : When you tighten the lock nuts (12), apply opposite force by____ use of the flats on the studs (20).
R R (28) Safety the lock nuts (12) to the locking devices (14) with MISCELLANEOUS (Material No. 19-010).
R R (29) Apply SEALANTS (Material No. 09-013) to the lock nuts (12), the locking devices (13) and (14) and to the end of the studs (20).
(30) Hold the rod-ends (28) and TORQUE the lock nuts (29) to between 0.4 and 0.5 m.daN (35.39 and 44.24 lbf.in).
(31) Make sure that the rod-ends (28) are parallel to the MLG bracket lugs.
R R NOTE : When you tighten the lock nuts (29), apply opposite force by____ use of the flats on the studs (20).
(32) Measure the dimension X. It must not be more than 44.7 mm (1.7598 in.).
(33) Safety the lock nuts (29) with MISCELLANEOUS (Material No. 19-010).
(34) Install the cover plates (11) and the screws (30).
(35) TORQUE the screws (30) to between 0.17 and 0.23 m.daN (15.04 and 20.35 lbf.in).
(36) Apply SEALANTS (Material No. 09-013) to the cover plates (11) and the screws (30).
(37) Hold the eye-ends (3) and TORQUE the lock nuts (10) to between 0.4 and 0.5 m.daN (35.39 and 44.24 lbf.in).
(38) Make sure that the eye-ends (3) are parallel to the MLG bracket lugs.
(39) Measure the dimension W. It must not be more than 40.0 mm (1.5748 in.).
(40) Safety the lock nuts (10) with MISCELLANEOUS (Material No. 19-010).
(41) TORQUE the nuts (23) to between 1.8 and 2.0 m.daN (13.27 and 14.74 lbf.ft).
R 1EFF : 051-099, 102-149, 151-199, 201-299, 1 32-12-14Page 445 1401-499, 1Aug 01/05 1 1 1CES 1
(42)
At the position F, install and safety the new cotter pin (21).
(43)
At the position C, install and safety the new cotter pin (22).
(44)
TORQUE the nuts (7) to between 1.15 and 1.35 m.daN (101.76 and 119.46 lbf.in).
(45)
Install and safety the new cotter pins (6).
(46)
Apply SEALANTS (Material No. 09-013) to the parts that follow: NOTE : Make sure that the sealant does not enter the spherical
____ bearings of the eye-ends (3) and the rod-ends (28).
-the bolts (5) and the washers (4)
-the bolts (9), the washers (8) and the nuts (7) R - the lock nuts (10) and the eye-ends (3)
-
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(47)
