(c)
Put the stop (64) in position on the support (65).
(d)
Install the screws (62), the washers (63) and (66) and the nuts (68).
(e)
TORQUE the nuts (68) to between 0.6 and 0.7 m.daN (53.09 and
61.94 lbf.in) and safety them with the new cotter pins (67).
(f)
Put the upper arm of the torque links and the washers (69) and
(70) in position.
(g)
Install the upper shaft (73), align the rigging holes.
(h)
Clean the screw (74) with CLEANING AGENTS (Material No. 11-004A) and dry it with filtered compressed air.
R 1EFF : 001-004, 052-054, 106-149, 229-299, 1 32-21-27Page 425 1303-399, 401-499, 1Aug 01/05 1 1 1CES 1
(i)
Apply a light coat of SPECIAL MATERIALS (Material No. 05-047) to the screw (74). Install the screw and correctly put the thread hole in position.
(j)
Install the washer (72).
(k)
Install the nut (71) but do not tighten at this time.
(l)
Apply a bead of SEALANTS (Material No. 09-001) at the screw head (74)/gear leg interface.
(3)
Install the target support (Ref. Fig. 404/TASK 32-21-27-991-005)
(a)
Put the casing (134) in position on the screw (143).
(b)
Install the screw (141) and the new lockwasher (142).
(c)
Tighten the screw (141) and safety it with the lockwasher (142).
(d)
Install the screw (133), the washers (132) and (131) and the nut (130).
(e)
TORQUE the nut (130) to between 0.6 and 0.7 m.daN (53.09 and
61.94 lbf.in).
(f)
Put the rod (135) in position. Install the screw (136), the washer (138) and the nut (139).
(g)
TORQUE the nut (139) to between 0.6 and 0.75 m.daN (53.09 and
66.37 lbf.in).
(h)
Safety the nut (139) with the new cotter pin (140).
(i)
Tighten the nut (71).
(4)
Connect the center hinge (Ref. Fig. 402/TASK 32-21-27-991-001)
(a)
Make sure that there is no friction point when each torque link arm moves.
(b)
Clean the threads of the shaft (1) and the nut (6) with CLEANING AGENTS (Material No. 11-004A) and dry them with filtered compressed air.
R 1EFF : 001-004, 052-054, 106-149, 229-299, 1 32-21-27Page 426 1303-399, 401-499, 1Aug 01/05 1 1 1CES 1
(c)
Apply a light coat of COMMON GREASE (Material No. 04-022) to the washers (2), (3) and (4) and to the shaft (1).
(d)
Align the center bores of the upper and lower arms of the torque links and install the washers (2), (3) and (4).
(e)
Install the shaft (1).
(f)
Make sure that the play at the torque link hinges is correct (Ref. TASK 32-21-00-200-003).
(g)
Do the torque procedure on the nut (6)
1_ Apply a layer of SPECIAL MATERIALS (Material No. 05-047) to
the washer (5) and install it on the shaft (1).
2_ Apply a layer of SPECIAL MATERIALS (Material No. 05-047) to
the threads of the nut (6) and install it.
3_ TORQUE the nut (6) to 9 m.daN (66.37 lbf.ft) and loosen the
nut (6). Do this three times.
4_ Loosen the nut (6) to get a clearance between 0.02 mm (0.0007
in.) and 0.1 mm (0.0039 in.).
5_ Make sure that you can align a hole of the nut (6) with the
slot of the shaft (1) and keep the clearance given above.
If not:
- loosen the nut (6),
- remove the washer (5),
- adjust the thickness of the washer (5) to get the clearance
given above with a hole of the nut (6) aligned with the slot
of the shaft (1),
NOTE : The total thickness of the washer (5) (shoulder____
included) must not be less than 4 mm (0.1574 in.). If
the thickness of the washer (5) is less than 4 mm
(0.1574 in.), replace it with the new washer (5).
- do a passivating treatment on the reworked surface (Ref. CMM
320901),
- do the torque procedure on the nut (6) again.
6 Apply a layer of SPECIAL MATERIALS (Material No. 05-047) to
_ the threads of the screw (10).
R 1EFF : 001-004, 052-054, 106-149, 229-299, 1 32-21-27Page 427 1303-399, 401-499, 1Aug 01/05 1 1 1CES 1
7_ Install the screw (10), the washer (7), the nut (8) and
tighten it.
8_ Install the new cotter pin (9) on the nut (8).
(5)
Apply a layer of SEALANTS (Material No. 09-001) to the areas identified E.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(113)
