(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
1EFF : ALL 1 32-12-14Page 413 1 1 Aug 01/05 1 1 1CES 1
R (4) Make sure that the lockwire around the lock nuts (2) and (10) is
R satisfactory. If the lockwire is not satisfactory you must do the Installation of a Replacement MLG Fixed Fairing Assembly (Ref. TASK 32-12-14-400-002).
(5) Make sure that the fixed fairing assembly (1) is in a servicable condition.
Subtask 32-12-14-420-055
B. Installation of the MLG Fixed Fairing Assembly
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : THE WEIGHT OF THE FIXED FAIRING IS 34kg (75lb).
_______
(1)
Hold the fixed fairing (1) in position on the brackets of the MLG leg.
(2)
At the position C, install the bush (11), the bolt (18), the washer
(15) and the nut (14).
(3)
At the position F:
**ON A/C 001-049, 051-060, 101-101,
(Ref. Fig. 402/TASK 32-12-14-991-002)
R **ON A/C 051-099, 102-149, 151-199, 201-299, 401-499,
Post SB 52-1100 For A/C 051-060,
(Ref. Fig. 402A/TASK 32-12-14-991-002-A)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-12-14Page 414 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Fixed Fairing - Rigging
Figure 402/TASK 32-12-14-991-002
R 1EFF : 001-049, 051-060, 101-101, 1 32-12-14Page 415 1 1 May 01/05 1 1 1CES 1
Fixed Fairing - Rigging Figure 402A/TASK 32-12-14-991-002-A
R 1EFF : 051-099, 102-149, 151-199, 201-299, 1 32-12-14Page 416 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(a)
Install the bush (17), the bolt (18), the washer (15) and the nut (14).
(b)
Make sure that the dimensions 'Y' and 'Z' are between 1.3 mm (0.0511 in.) and 2.7 mm (0.1062 in.).
(4)
At the positions B, D and E, install the bushes (6), the bolts (7), the washers (5) and the nuts (3).
(5)
TORQUE the nuts (3) to between 1.15 and 1.35 m.daN (101.76 and 119.46 lbf.in).
(6)
Safety the nuts (3) with the new cotter pins (4).
(7)
At the position F:
(a)
TORQUE the nut (14) to between 1.15 and 1.35 m.daN (101.76 and
119.46 lbf.in).
(b)
Safety the nut (14) with a new cotter pin (12).
(8)
At the position C:
(a)
TORQUE the nut (14) to between 1.80 and 2.0 m.daN (13.27 and
14.74 lbf.ft).
(b)
Safety the nut (14) with a new cotter pin (13).
(9)
Clean the components that follow with a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026):
-
the bolts (7) and (18)
-
the washers (5) and (15)
-
the nuts (3) and (14).
(10)
Apply a thin layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the components that follow:
-
the bolts (7) and (18)
-
the nuts (3) and (14).
(11)
Install the bonding strap (8) on the screw (21) and install the nut
(9) (Ref. TASK 20-28-00-912-004).
(12)
Hold the head of the screw (21) and TORQUE the nut (9) to between
0.35 and 0.45 m.daN (30.97 and 39.82 lbf.in).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-12-14Page 417 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(13)
Apply a thin layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the cover plate (20) and the screws (19).
(14)
Install the cover plate (20) with the screws (19).
(15)
TORQUE the screws (19) to between 0.17 and 0.23 m.daN (15.04 and
20.35 lbf.in).
**ON A/C 301-399,
Subtask 32-12-14-420-057-A
A. Preparation For Installation
(1)
Clean the component interfaces and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM LANDING GEAR 起落架3(39)
