4. Procedure_________
(Ref. Fig. 301/TASK 32-42-12-991-002)
Subtask 32-42-12-020-052
A. Removal of the Filter 2584GM
(1) Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
(2) Remove and discard the lockwire from the bowl (4) and the filter head (1).
(3) Remove the bowl (4) and the filter cartridge (3). Discard the filter cartridge (3).
Subtask 32-42-12-560-051
R B. Preparation for Installation
R (1) Clean the component interface and/or the adjacent area.
R (2) Do an inspection of the component interface and/or the adjacent area.
R (3) Make sure that the parts retained from the removed component are clean and in the correct condition.
R (4) If the red clogging indicator is out, push it in to set it.
R R R R R (5) Apply the HYDRAULIC FLUIDS (Material No. 02-003), HYDRAULIC FLUIDS (Material No. 02-003A), HYDRAULIC FLUIDS (Material No. 02-003B) or HYDRAULIC FLUIDS (Material No. 02-003C) to: - the threads of the bowl (4) - the packing that is installed in the new filter cartridge (3).
Subtask 32-42-12-420-053
R C. Installation of Brake Filter 2584GM
R (1) Install the filter cartridge (3) in the bowl (4).
R (2) Put the bowl (4) in position and tighten the bowl to the filter head (1) by hand.
R Hydraulic Brake Filter 2584GM Figure 301/TASK 32-42-12-991-002
1EFF : 1 1 1CES ALL 1 111 32-42-12 Page 305 May 01/05
R (3) Safety the bowl (4) to the filter head (1) with corrosion-resistant steel lockwire 0.8 mm (0.032 in.) dia.
Subtask 32-42-12-865-054
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GG, 2GG, 3GG, 4GG, 1701GK, 1702GK.
Subtask 32-42-12-560-052
E. Connection of the PTU Isolation Coupling
(1)
Connect the PTU isolation coupling (Ref. TASK 29-23-00-860-002).
(a)
If necessary fill the reservoir of the Green hydraulic system to the correct level (Ref. TASK 12-12-29-611-001).
(b)
Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001).
(2)
Test of the System
(a)
Remove the warning notice(s).
(b)
Operate the brakes and make sure that:
-the clogging indicator stays in,
-there is no hydraulic fluid leakage from the hydraulic brake filter 2584GM.
(c)
Remove the container.
(d)
Remove the access platform(s).
5. Close-up
________
Subtask 32-42-12-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the applicable MLG door (Ref. TASK 32-12-00-410-001).
1EFF : ALL 1 32-42-12Page 306 1 1 May 01/05 1 1 1CES 1
(3) Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
1EFF : ALL 1 32-42-12Page 307 1 1 Feb 01/98 1 1 1CES 1 TASK 32-42-12-960-001
Replacement of the Clogging Indicator
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific 1 ACCESS PLATFORM 3M (10 FT)
No specific 1 CONTAINER 1 L (1/4 USGAL)
No specific 2 WARNING NOTICE
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(141)
