(2)
Do a check of the wheel for damage, no damage is permitted.
5. Close-up
________
Subtask 32-41-00-942-055
A. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make an entry in the log book.
R 1EFF : ALL 1 32-41-00Page 413 1 1 May 01/05 1 1 1CES 1
TASK 32-41-00-040-003 Check of the Main Wheel when one tie bolt is missing
1. Reason for the Job
__________________
Refer to the MMEL TASK: 32-41-02
Main Wheel Tie Bolts
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-41-11-000-006 Removal of the MLG Wheel (2649GM,2650GM,2651GM,2652GM) 32-41-11-400-006 Installation of the MLG Wheel (2649GM,2650GM,2651GM,2652GM)
3. Job Set-up
__________ Subtask 32-41-00-941-057
A. Not applicable
4. Procedure
_________ Subtask 32-41-00-210-074
A. Check of the related Main Wheel
(1)
Remove the related main wheel (Ref. TASK 32-41-11-000-006).
(2)
Make sure that no broken pieces of the tie bolt are in the wheel. If there are pieces of the tie bolt in the wheel, remove them.
(3)
Do a check the wheel for damage, no damage is permitted.
(4)
Install the main wheel (Ref. TASK 32-41-11-400-006).
R 1EFF : ALL 1 32-41-00Page 414 1 1 May 01/05 1 1 1CES 1
5. Close-up
________ Subtask 32-41-00-942-056
A. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make an entry in the log book.
R 1EFF : ALL 1 32-41-00Page 415 1 1 May 01/05 1 1 1CES 1R **ON A/C 001-049, 101-149, 151-199, 201-299,
TASK 32-41-00-040-004
Deactivation of the Main Wheel Hupcap
1. Reason for the Job
__________________
Refer to the CDL TASK: 32-2
Main Wheel Hubcap
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific wheel chocks
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change
29-24-00-863-001 Pressurize the Yellow Hydraulic System with the
Electric Pump
32-41-00-991-035 Fig. 402
3. Job Set-up
__________
Subtask 32-41-00-941-058
A. Safety Precautions
(1)
On the panel 400VU:
-put a warning notice in position to tell persons not to operate the landing gear control lever.
(2)
Make sure that the wheel chocks are in position.
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-00Page 416 1 1 May 01/05 1 1 1CES 1 Subtask 32-41-00-865-058
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
Subtask 32-41-00-860-057
C. Aircraft Maintenance Configuration
(1)
On the panel 110VU :
-make sure that the PARK BRK control switch is set to ON.
(2)
On the panel 400VU:
-make sure that the brake pressure indication on the Yellow brake-pressure triple indicator is correct.
-If necessary pressurize the brake accumulator with the Yellow pump (Ref. TASK 29-24-00-863-001).
(3)
Lift the related axle with a jack (Ref. TASK 07-12-00-582-002).
(4)
Fully deflate the tire.
4. Procedure
_________ (Ref. Fig. 402/TASK 32-41-00-991-035) Subtask 32-41-00-040-052
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(50)
