曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (8) Make sure that the cockpit floor panels 212GF and 212NF are removed 
R  (Ref. TASK 53-12-11-000-001). 
R  (9) Make sure that the forward fuselage floor panels 222CF, 222EF and 
R  232DF are removed (Ref. TASK 53-12-12-000-001). 
R  (10) For the cables (13), (15), (25) and (27): 
R  - make sure that the RIGGING PIN (98A27801001000) is in the Pin 1 
R  position 
R  - make sure that the RIGGING PIN (98DNSA20208150) is in the Pin 2 
R  position. 
R  (11) For the cables (37), (38), (39) and (40): 
R  - make sure that the RIGGING PIN (98DNSA20208150) is in the Pin 2 
R  position 
R  - make sure that the RIGGING PIN (98DNSA20208060) is in the Pin 3 
R  position. 
R  **ON A/C ALL
 Subtask 32-33-16-869-057
 C. Flight Configuration Precautions
 (1) If you did not open the LGCIU circuit breakers, make sure that the
 electrical circuits are de-energized (Ref. TASK 24-41-00-862-002).
 (2) If you opened the LGCIU circuit breakers, make sure that the flight
 configuration precautions were obeyed (Ref. TASK 32-00-00-860-001).

 

 D. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
 4. Procedure
_________ Subtask 32-33-16-420-058
 A. Preparation for Installation
 (1)
 Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).

 (2)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (3) Do an inspection of the component interface and/or the adjacent area. Subtask 32-33-16-420-052
 B. Installation of the MLG Free-Fall Extension Cables (39) and/or (40)
 (Ref. Fig. 407/TASK 32-33-16-991-004, 408/TASK 32-33-16-991-005)

 (1)
 Put the cable(s) (39) and/or (40) around the pulleys and through the structure.

 (2)
 Attach the cable(s) (39) and/or (40) to the pulley (83).

 (3)
 When necessary (for RH cables only) install the fairlead(s) (82).

 (4)
 Release the cable(s) (37) and/or (38) from the structure.

 (5)
 Connect each cable as necessary to its related cable with the turnbuckle(s) (41).

 (6)
 Temporarily attach the locking clips (42).

 1EFF : ALL 1 32-33-16Page 438 1 1 Feb 01/03R 1 1 1CES 1

 (7)
 Install these items together:

 -
the tubes (75) and the washers (76)

 -
the tubes (78) and the washers (79).

 

 (8)
 Safety the tubes with the new cotter-pin (77) and cotter-pin (80).

 (9)
 At the cable pulley assembly on FR 41, install these items together:

 -
the cable guard assembly (85)

 -
the pins (84), the washers (86) and the nuts (87).

 

 (10)
 Safety the nuts (87) with MISCELLANEOUS (Material No. 19-010). Subtask 32-33-16-420-053

 C. Installation of the MLG Free-Fall Extension Cables (37) and/or (38) (Ref. Fig. 407/TASK 32-33-16-991-004, 409/TASK 32-33-16-991-009)
 (1)
 Clean the pressure-seal-flanges (58) and (60) with CLEANING AGENTS (Material No. 11-026) to remove the sealant and paint.

 (2)
 Put the sleeve (63) and the pressure-seal-flanges (58) and (60) on the applicable cable correctly.

 (3)
 Put the cable(s) (37) and/or (38) around the pulleys and through the structure.

 (4)
 Attach the cable(s) (37) and/or (38) to the pulley (65).

 (5)
 Release the cable(s) (39) and/or (40) from the structure.

 (6)
 Connect each cable as necessary to its related cable with the turnbuckle(s) (41).

 

 (7)
 Temporarily attach the locking clips (42). Subtask 32-33-16-420-054

 D. Installation of the Cable Pressure Seals
 (1)
 Apply the special material SPECIAL MATERIALS (Material No. 05-002) (5.7070.0) to the pressure-seal flanges (58) and (60) and the bolts (62).

 (2)
 Assemble the cable pressure-seal(s) with these items:

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(28)