B. Aircraft Maintenance Configuration
 (1)
 Make sure that the PARK BRK control switch is set to ON. NOTE : On the panel 400VU, make sure that brake pressure indication

____ on the Yellow brake-pressure triple indicator is correct. If necessary pressurize the brake accumulator with Yellow pump (Ref. TASK 29-10-00-863-002).

 (2)
 Make sure that the related axle is lifted with a jack (Ref. TASK 07-12-00-582-002).

 4. Procedure
_________ (Ref. Fig. 401/TASK 32-41-11-991-010) NOTE : If the wheel is equipped with a pressure sensor seal cap, make sure
____ that the seal cap is properly installed and secured with nut and cotter pin.
 Subtask 32-41-11-210-054
 A. Tires of Different Type
 (1) Obey the tire mixability precautions (Ref. TASK 32-41-00-910-001). Subtask 32-41-11-560-060-A
 B. Preparation of the Wheel before Installation CAUTION : MAKE SURE THAT THE GREASE USED FOR THE AXLE SLEEVE IS THE SAME
_______ AS THE GREASE USED FOR THE BEARINGS (CONE AND CAGE). IF YOU USE A DIFFERENT GREASE, YOU CAN CAUSE DAMAGE TO THE BEARINGS.
 (1)
 Make sure (if the tire mixability is not allowed) that the wheel for installation has the same type of tire (radial or cross-ply) as the other wheel on the MLG.

 (2)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (3)
 Clean the component interface and/or the adjacent area.

 (4)
 Do an inspection of the component interface and/or the adjacent area.

R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-11Page 407 1 1 Config-1 May 01/05 1 1 1CES 1

 (5) Remove quantities of brake dust.
 (6) Examine the brake for hydraulic leaks, from the hose connections and the pistons.
 (7) Examine the brake heat pack. Make sure that: - there is no hydraulic fluid contamination of the carbon parts - there is not too much wear in the drive slots areas and the rivet holes - there is no foreign object damage - there are too many holes, cracks or chips - there are no soft areas, where carbon is missing or crushed - there are no broken rotors or stators - there are no broken or missing links - there are no broken or missing rivets - there is no other possible damage.
 NOTE : If the brake is unserviceable it must be replaced (Ref. TASK____ 32-42-27-000-001) and (Ref. TASK 32-42-27-400-001).
 (8) Make sure that the driving keys on the brake rotors are correctly aligned.
 (9) Make sure that the splines of the tachometer drive shaft (13) and the splines of the hubcap (10) are in the correct condition.
 NOTE : If you find wear, replace the related parts.____
 (10) Clean the axle sleeve (2) with CLEANING AGENTS (Material No. 11-002) and dry it with filtered compressed air. 
R R  (11) Do a visual inspection of the axle protective sleeve to make sure that it is in correct condition. 
R  (12) Make sure that the retaining ring (3) of the axle sleeve (2) is in the correct position. The ring must be correctly engaged in its groove. If not, the axle sleeve is not installed correctly and you can damage it when you install the axle nut. 
R  (13) Clean the splines (10) of the tachometer hubcap and the splines (13) of the tachometer drive shaft with CLEANING AGENTS (Material No. 11-002) and dry with filtered compressed air. 
R  (14) Apply a thin layer of COMMON GREASE (Material No. 04-003) on the splines (10) and (13). 

R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-11Page 408 1 1 Config-1 May 01/05 1 1 1CES 1

R (15) Apply a thin layer of COMMON GREASE (Material No. 04-022) or COMMON

 GREASE (Material No. 04-035) to the axle sleeve (2).
 WARNING : YOU MUST NOT PUT TOO MUCH GREASE ON THE AXLE SLEEVE. A VERY
_______ HOT BRAKE CAN CAUSE THE GREASE TO BURN AND CAUSE A FIRE.
 NOTE : Do not mix Material 04-022 with Material 04-035. You can use
____ Material 04-035 as an alternative to material 04-022. Clean and degrease the parts before you use Material 04-035.
R (16) Apply COMMON GREASE (Material No. 04-022) or COMMON GREASE (Material No. 04-035) to all the bearing surfaces and to the threads of the axle.
R (17) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces.
 Subtask 32-41-11-420-061-A
 C. Installation of the Wheel
 WARNING : BE CAREFUL WHEN YOU REMOVE/INSTALL THE WHEEL AND TIRE ASSEMBLY
_______ TO PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE WHEEL, AXLE OR OTHER EQUIPMENT. THE ASSEMBLY IS VERY HEAVY (BETWEEN 130 KG AND 200 KG (290 LBS AND 440 LBS)).
 CAUTION : MAKE SURE THAT THE AXLE THREAD PROTECTOR IS CORRECTLY INSTALLED
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(67)