(4)
 Install the washer (13) and the nut (14). Safety the nut with the cotter pin (15).

 1EFF : ALL 1 32-33-15Page 409 1 1 Feb 01/98 1 1 1CES 1 Subtask 32-33-15-080-050

 D. Remove the Rigging Pins
 (1)
 Remove the PIN, RIGGING - RUDDER CONTROL (98A27901002000) (9) from the lower bellcrank (10).

 (2)
 Remove the RIGGING PIN (98A27801001000) (1) from the quadrant (2).

 (3) Remove the shim(s) from the handle. Subtask 32-33-15-720-050
 E. Functional Test
 (1) Do the functional test of the free fall extension (Ref. TASK 32-33-00-720-001).
 5. Close-up
________ Subtask 32-33-15-410-050
 A. Close Access

 (1)
 Close the lateral avionics-compartment door 822.

 (2)
 Close the doors of the nose landing gear (Ref. TASK 32-22-00-410-001).

 (3) Install the cockpit floor panel 211FF (Ref. TASK 53-12-11-400-001). Subtask 32-33-15-942-050
 B. Removal of the Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 32-33-15Page 410 1 1 Feb 01/98 1 1 1CES 1 CABLES - FREE FALL EXTENSION - REMOVAL/INSTALLATION

___________________________________________________
 TASK 32-33-16-000-001
 Removal of the NLG Free-Fall Extension Cables
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice No specific wedge 98A27801001000 1 RIGGING PIN 98A27901002000 1 PIN, RIGGING - RUDDER CONTROL
 1EFF : ALL 1 32-33-16Page 401 1 1 May 01/05R 1 1 1CES 1

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 32-00-00-481-001 Installation of the Safety Devices on the Landing
 Gears
R 32-00-00-860-001 Flight Configuration Precautions with Electrical
R Power 32-22-00-010-001 Nose Gear Doors - Ground Doors Opening 53-12-11-000-001 Removal of the Cockpit Floor Panels from FR1 Thru FR12 53-12-12-000-001 Removal of the Cabin Floor Panels from FR12 thru FR24 32-33-16-991-006 Fig. 401 32-33-16-991-001 Fig. 402 32-33-16-991-002 Fig. 403
 3. Job Set-up
__________
 (Ref. Fig. 401/TASK 32-33-16-991-006)
 Subtask 32-33-16-941-050
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).

 (3)
 On the panel 400VU:

 -Make sure that the landing-gear control-lever 6GA is in the DOWN position.
 -Put a warning notice in position to tell persons not to operate the landing gear.

 (4)
 On the panel 110VU, make sure that the GRAVITY GEAR EXTN handle is folded into the center console.

 (5)
 Install a wedge on each side of the GRAVITY GEAR EXTN handle to lock the handle in position.

 1EFF : ALL 1 32-33-16Page 402 1 1 May 01/05 1 1 1CES 1

 Forward Fuselage Floor Panels
 Figure 401/TASK 32-33-16-991-006
 1EFF :  ALL  1  32-33-16 Page 403 
1  1  Feb 01/98
 1  1
 1CES  1

 Subtask 32-33-16-010-050
 B. Get Access
 (1)
 Open the NLG doors (Ref. TASK 32-22-00-010-001).

 (2)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(19)