R 1EFF : 051-099, 1 32-41-12Page 413 1 1 May 01/05 1 1 1CES 1 1EFF : ALL 1 32-41-12Page 414 1 1 May 01/05 1 1 1CES 1R **ON A/C ALL

R  (3) Engage the drive dog (13) in the fork of the rotating mechanism. 
R  (4) Install the screws (14), the washers (15). 
R  (5) TORQUE the screws (14) to between 0.4 and 0.51 m.daN (35.39 and 45.13 
R  lbf.in) and safety them with corrosion resistant steel lockwire 0.8mm 
R  (0.032 in) dia. 
R  **ON A/C ALL
 Subtask 32-41-12-860-051
 D. Aircraft Maintenance Configuration
 (1) Inflate the tire to the unloaded pressure (Ref. TASK 12-14-32-614-
001).
 (2) Lower the aircraft on its wheels (Ref. TASK 07-12-00-582-001).
 (3) Make sure that the pressure of the tire is correct (Ref. TASK 32-41-
00-210-003). 
R  **ON A/C 051-099, 
R  Subtask 32-41-12-865-052 
R  E. Make sure that this(these) circuit breaker(s) is(are) closed: 
R  1GV 
R  Subtask 32-41-12-720-050 
R  F. Do the functional test of the tire pressure indicating system (Ref. TASK 
R  32-49-00-720-001).

 5. Close-up
________
 Subtask 32-41-12-942-051

 A. Removal of the Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the warning notice(s).

 1EFF : ALL 1 32-41-12Page 415 1 1 May 01/05 1 1 1CES 1

 TASK 32-41-12-000-002 Removal of the Axle Sleeve
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-41-12-000-001 Removal of the NLG Wheel (2659GM,2660GM) 32-41-12-991-002 Fig. 402
 3. Job Set-up
__________ Subtask 32-41-12-010-050
 A. Get access
 (1) Remove the related landing gear wheel (Ref. TASK 32-41-12-000-001).
 4. Procedure
_________ (Ref. Fig. 402/TASK 32-41-12-991-002) Subtask 32-41-12-020-051
 A. Removal of the Axle Sleeve
 (1)
 Remove the retaining ring (3).

 (2)
 Remove the axle sleeve (2).

 1EFF : ALL 1 32-41-12Page 416 1 1 May 01/05 1 1 1CES 1

 Axle Sleeve
 Figure 402/TASK 32-41-12-991-002
 1EFF :  ALL  1  32-41-12 Page 417 
1  1  May 01/05
 1  1
 1CES  1

 TASK 32-41-12-400-002 Installation of the Axle Sleeve
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-022  USA MIL-PRF-81322 GRADE 2 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE (Ref. 20-31-00)
 Material No. 11-002  USA MIL-PRF-680 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT) (Ref. 20-31-00)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-41-12-400-001  Installation of the NLG Wheel (2659GM,2660GM)
 3. Job Set-up
__________ Subtask 32-41-12-640-052
 A. Preparation for Installation
 (1)
 Clean the axle (1) with CLEANING AGENTS (Material No. 11-002). Dry it with filtered compressed air .

 (2)
 Lightly lubricate the axle (1) and the axle protective sleeve (2) with COMMON GREASE (Material No. 04-022).

 1EFF : ALL 1 32-41-12Page 418 1 1 May 01/05 1 1 1CES 1

 4. Procedure
_________ Subtask 32-41-12-420-051
 A. Installation of the Axle Sleeve
 (1)
 Install the axle sleeve (2).

 (2)
 Install the retaining ring (3).

 5. Close-up
________ Subtask 32-41-12-410-050
 A. Close access
 (1)
 Install the related wheel (Ref. TASK 32-41-12-400-001).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LANDING GEAR 起落架6(81)