曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (3) Deflate the tire completely. ;
 NOTE : If you must remove the wheel for access it is not necessary to____ deflate the tire if: - the tire is in correct condition and - the tire pressure is in the Normal Operating Range. (Ref. TASK 32-41-00-210-003) If you have not these two conditions you must deflate the tire.

 

 4. Procedure
_________ R **ON A/C 001-049, 101-149, 151-199, 201-299, 301-399, 401-499,
 (Ref. Fig. 401/TASK 32-41-12-991-001)
 **ON A/C 051-099,

 (Ref. Fig. 401A/TASK 32-41-12-991-001-A) R **ON A/C 001-049, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 32-41-12-010-051
 A. Get access
 (1)
 Cut and remove the corrosion resistant steel lockwire.

 (2)
 Remove the screws (7) and the washers (8).

 (3) Remove the hubcap (6).
 Subtask 32-41-12-020-050

 B. Removal of the NLG wheel
 (1)
 Remove and discard the two cotter pins (4).

 (2)
 Remove the nuts (3), the washers (2) and the bolts (5).

 (3)
 Remove the casing (9).

 (4)
 Remove the axle nut (10) with the ADAPTOR NLG (J47549).

 (5)
 Install the PROTECTOR NLG (J47548).

 (6)
 Remove the wheel.

 1EFF : ALL 1 32-41-12Page 403 1 1 Aug 01/05 1 1 1CES 1

 Nose Gear Wheel
 Figure 401/TASK 32-41-12-991-001

R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-12Page 404 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

R  Nose Gear Wheel 
R  Figure 401A/TASK 32-41-12-991-001-A 
R 1EFF :  051-099,  1  32-41-12 Page 405 
1  1  May 01/05
 1  1
 1CES  1

 

R  **ON A/C 051-099, 
R  Subtask 32-41-12-010-051-A 
R  A. Get access 
R  (1) Cut and remove the corrosion resistant steel lockwire. 
R  (2) Remove the screws (14) and the washers (15). 
R  (3) Release the grommet (16) and remove the hubcap (12). 
R  (4) Disconnect the electrical connector (11) from the connector (18) and 
R  install the blanking cap on the disconnectd connector. 
R  WARNING : MAKE SURE THAT THE TIRE IS FULLY DEFLATED._______ 
R  (5) Remove and discard the cotter pin (5). Remove the nut (6). 
R  (6) Remove the pressure transducer (4). 
R  (7) Remove the preformed packings (3) and discard them. 
R  Subtask 32-41-12-020-050-A 
R  B. Removal of the NLG Wheel 
R  (1) Remove and discard the two cotter pins (9). 
R  (2) Remove the nuts (8), the washers (7) and the bolts (10). 
R  (3) Remove the axle nut (17) with the ADAPTOR NLG (J47549). 
R  (4) Install the PROTECTOR NLG (J47548). 
R  (5) Remove the wheel. 

R 1EFF : 051-099, 1 32-41-12Page 406 1 1 May 01/05 1 1 1CES 1

R **ON A/C ALL

 TASK 32-41-12-400-001
 Installation of the NLG Wheel (2659GM,2660GM)
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific  warning notice
R No specific  Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
 (15.00 to 150.00 lbf.ft) No specific Torque Wrench : range 6.00 to 36.00 m.daN
 (50.00 to 260.00 lbf.ft) J47549 1 ADAPTOR NLG
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
No specific  corrosion resistant steel lockwire 0.8mm (0.032 in) dia
 Material No. 04-022  USA MIL-PRF-81322 GRADE 2
 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
 (Ref. 20-31-00)

 Material No. 04-035
 SYNTHETIC WHEEL BEARING GREASE (Ref. 20-31-00)

 Material No. 11-002  USA MIL-PRF-680
 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
 (Ref. 20-31-00)

 1EFF : ALL 1 32-41-12Page 407 1 1 May 01/05 1 1 1CES 1
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(78)