(c)
Examine the routing of the hoses.
-
Make sure that the hoses do not rub against other hoses and lines, partitions or units.
-
Make sure that the hoses are not twisted.
1EFF : ALL 1 32-40-00Page 602 1 1 May 01/05 1 1 1CES 1
-Make sure that the play of the hose is sufficient. To do this move the middle of the hose up and down.
(3)
Check of the hydraulic lines
(a)
Make sure that there is no distortion, that there are no cracks that start. Make sure that there are no signs of shock, specially on the elbows and the bends of the lines and on the connection point with other units.
(b)
Make sure that the conduit rails or the metal parts cannot damage the lines in their housings.
(c)
Make sure that there are no leaks of hydraulic fluid on the connectors. Make sure that they are safetied correctly.
(d)
Make sure that the mountings, the clamp blocks of the lines and the attachment collars are installed correctly.
(4)
Check of the hydraulic units
(a)
Make sure that the units are installed correctly. Make sure that there are no leaks on the hydraulic connectors.
(b)
Make sure that the electrical connections are in the correct condition.
(5)
Check of the electrical wiring
(a)
Make sure that the electrical connectors are installed correctly and that they are safetied correctly.
(b)
Make sure that the electrical connectors do not have any contamination from the hydraulic fluids. If it is necessary, clean them.
(c)
Make sure that the wiring is fully protected and that it is in the correct condition.
(6)
Check of the nose landing gear Make sure that these components are installed correctly and that they are in the correct condition:
-
the electrical harnesses,
-
the connectors and plugs,
-
the in-flight braking-straps of the wheel of the nose landing gear.
R 1EFF : 001-049, 051-061, 101-102, 201-202, 1 32-40-00Page 603 1 1 May 01/05 1 1 1CES 1
(7)
Check of the main landing gear Make sure that these components are installed correctly and that they are in the correct condition:
-
the hydraulic lines (clamps),
-
the electrical harnesses,
-do a visual inspection to make sure that there are no signs of ageing, overheating, flaking and deformation,
-the connectors and plugs (tachometers).
(8)
Make sure that there is no hydraulic fluid: - on the unions and the points where the lines connect with the
units, - on the supply lines, - on the connecting blocks, - on the servo valve, - on the brakes (the bleed screws, the points where the lines connect
with the units and the pistons).
(9) Examine the connections of the wiring of the temperature sensor on the aft face of each brake assembly.
R **ON A/C 062-099, 103-149, 151-199, 203-299, 301-399, 401-499,
Subtask 32-40-00-210-051-A
A. Check of the Brake System
(1)
Full check
(a)
Do a check of the attach and hinge fittings. Make sure that:
-
they are installed correctly,
-
they are safetied correctly (with the cotter pins, the tabwashers, the lockwashers and the lockwire),
-that the pins, the screws, the nuts and the washers do not show signs of corrosion.
(b)
Make sure that the identification labels are installed correctly.
(c)
Make sure that the bonding braids are in the correct condition.
(2)
Check of the hydraulic hoses
(a) If a collar has a data which shows the month and the year of the limit of the life of the collar, examine this date and if it is expired you must replace the hose.
1EFF : ALL 1 32-40-00Page 604 1 1 Aug 01/05 1 1 1CES 1
(b)
Make sure that the clamps have the correct diameter. Make sure that they are correctly installed and that they are in the correct condition. Make sure that the clamps are not worn because they are not installed correctly, because of the vibration or the pressure surge.
(c)
Examine the routing of the hoses.
-
Make sure that the hoses do not rub against other hoses and lines, partitions or units.
-
Make sure that the hoses are not twisted.
-
Make sure that the play of the hose is sufficient. To do this move the middle of the hose up and down.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架6(40)
