3. Job Set-up
__________
Subtask 33-43-11-865-058
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 3LC1
122VU LIGHTING/EXT LT/RWY TURN OFF/L 1LC1 W06 FOR 3LC2
122VU LIGHTING/EXT LT/RWY TURN OFF/R 1LC2 W05
Subtask 33-43-11-860-050
B. Aircraft Maintenance Configuration
(1)
Make sure that the aircraft fuselage is in the horizontal position.
(2)
If not, do the precise leveling (Ref. TASK 08-22-00-200-001).
4. Procedure
_________
(Ref. Fig. 501/TASK 33-43-11-991-004) Subtask 33-43-11-820-050
A. Adjustment of the Turnoff Light with the Tool
(1)
Install the ADJUSTING TOOL - TURN OFF LIGHT (98D33403502000) (3) on the light.
(2)
Set the clinometer to an angle of 0 deg. +/-2 minutes. Put it against the tool (3) to make sure that the installation is horizontal.
(3)
Adjust the tool (3) if necessary and tighten the nuts (2).
(4)
Angular adjustment of the turnoff light
(a)
Set the clinometer to an angle of 2 deg. 30 minutes +/-2 minutes (nose down).
(b)
Put the clinometer on the applicable zone of the tool, perpendicular to the light and attach it with the strap.
(c)
Loosen the nuts (1), move the light to get the angle of 2 deg. 30 minutes +/-2 minutes.
(d)
TORQUE the nuts (1) to between 0.6 and 0.75 m.daN (53.09 and
66.37 lbf.in) and make sure that the adjustment is correct.
(e)
Remove the clinometer and the ADJUSTING TOOL - TURN OFF LIGHT (98D33403502000).
Adjustment of the Runway Turnoff Light
Figure 501/TASK 33-43-11-991-004
1EFF : 051-051, 1 33-43-11 Page 503
1 1 May 01/05
1 1
1CES 1
5. Close-up
________
Subtask 33-43-11-865-059
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1LC1, 1LC2
TASK 33-43-11-730-001- 01
Adjustment of the Runway Turnoff Light (3CL1, 3CL2) - Alternative Procedure
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2 MINUTES
_______ AFTER YOU DE-ENERGIZE THE ELECTRICAL CIRCUITS.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific screen No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
08-22-00-200-001 Precise Leveling AMM 11-21-08 P.Block 001 LEVELING AND WEIGHING 33-43-11-991-005 Fig. 502
3. Job Set-up
__________ Subtask 33-43-11-865-060
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 3LC1
122VU LIGHTING/EXT LT/RWY TURN OFF/L 1LC1 W06 FOR 3LC2
122VU LIGHTING/EXT LT/RWY TURN OFF/R 1LC2 W05
Subtask 33-43-11-860-051
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(17)
