(5) Remove the light (10) from its support (3).

 1EFF : ALL 1 33-46-12Page 406 1 1 May 01/05R 1 1 1CES 1

 TASK 33-46-12-400-001
 Installation of the Taxi Light (8LR)
 WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.

_______

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-002  USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-46-00-710-001 Operational Test of the Taxi and Take Off Lights R 33-46-12-730-001 Adjustment of the Taxi Light (8LR)

R **ON A/C 051-051,
R 33-46-12-991-001 Fig. 401A

 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 33-46-12-865-051

 A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
 -------------------------------------------------------------------------------
122VU LIGHTING/EXT LT/TAXI AND TAKE OFF/TAXI 1LR W08
 4. Procedure
_________ R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 33-46-12-420-050
 A. Installation of the Taxi Light
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Make sure that the filament of the bulb and the lens of the optical unit are in the correct condition.

 (4)
 Make sure that the clamp is correctly installed.

 (5)
 Put the light (10) on its support (3).

 (6)
 Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (1) and (9).

 (7)
 Install the light (10) in the lower fork on the support (3).

 (8)
 Put the washer (8) on the screw (9).

 (9)
 Install the screws (9) in the support (3).

 (10)
 Install the washer (7) and tighten the nut (6).

 (11)
 Turn the light to the upper forks.

 (12) Install the washers (2) on the screws (1).
 (13) Install the screws (1) in the support (3).
 (14) Install the washers (4) and tighten the nuts (5).
 (15) Remove the blanking caps from the electrical connector (12) and the
 socket (11).
 (16) Make sure that the electrical connector (12) and the socket (11) are
 in the correct condition.
 (17) Connect the electrical connector (12) to the socket (11) and lock it. 
R  **ON A/C 051-051, 
R  Subtask 33-46-12-420-050-A 
R  A. Installation of the Taxi Light 
R  (Ref. Fig. 401A/TASK 33-46-12-991-001) 
R  (1) Clean the component interface and/or the adjacent area. 
R  (2) Do an inspection of the component interface and/or the adjacent area. 
R  (3) Make sure that the filament of the bulb and the lens of the optical 
R  unit are in the correct condition. 
R  (4) Make sure that the clamp is correctly installed. 
R  (5) Put the light (10) on its support (3). 
R  (6) Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (1) and 
R  (9). 
R  (7) Install the light (10) in the lower fork on the support (3). 
R  (8) Put the washer (8) on the screw (9). 
R  (9) Install the screws (9) in the support (3). 
R  (10) Install the washer (7) and tighten the nut (6). 
R  (11) Turn the light to the upper forks. 
R  (12) Install the washers (2) on the screws (1).

R  (13) Install the screws (1) in the support (3). 
R  (14) Install the washers (4) and tighten the nuts (5). 
R  (15) Adjust the taxi light (Ref. TASK 33-46-12-730-001). 
R R  (16) Remove the blanking caps from the electrical connector (12) and the socket (11). 
R R  (17) Make sure that the electrical connector (12) and the socket (11) are in the correct condition. 
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護(hù)手冊 AMM LIGHTS 燈光2(28)